Tag: range visit

Categories
1911 Duty range report range visit Tisas

Revisiting The Tisas Duty 1911

I’ve been keeping a running tally of notes after visiting the range – keep in mind that I’ve not been to the range with this particular gun in quite a while (2022). Here’s the latest version of my notes:

UPDATE 1:

  1. Range photos with detailed captions are at https://photos.app.goo.gl/yrLbWQNMmDjgJCzV8. Note: I’m not sure if Reddit will choke on Google’s URL shortener – I’ve had problems with it in the past.
  2. I brought 2 Wilson Combat mags with me, the two that the gun came with, and 1 ACT mag from another 1911. The ACT mag choked the gun once, and I knew it would be problematic because it’s been acting up the last few range visits (ie, it wasn’t an ammo issue). I bought another WC mag from the range store – it will replace the ACT mag. I will keep the ACT mag in case I need to scavenge parts from it.
  3. The B45R loved PMC Bronze 230-gr FMJ and I shot 50 rounds of it (this ammo always feels peppy). The other ammo I used was International 155-gr frangible ammo. That ammo is crappy but it never choked the B45R. My Metro Arms hates it. I also noticed slide slowdown (an indication of low powder charge) but only when shooting it out of the Metro Arms…I didn’t notice any of that with the B45R. I shot 100 rounds of the International ammo.
  4. I bought some G10 grips to replace the cheap-feeling grips that came with the gun. They work very well, and I expected nothing less (all of my other 1911s are using G10s).
  5. Issues:
    1. The WC mags will sometimes hang up in the mag well. It seems that the magazine catch/release is blocking insertion. If I hammer up on the mag, it blasts past but smacks into the upper portion of the gun (that’s probably not a good thing). If I actuate the release button a tad, the mag is allowed past. I’m hoping this issue will go away. This only happens with the WC mags. I’ve three 7-round Mecgar mags on the way here and they should arrive tomorrow. I’ll see if those get hung up. UPDATE: Found someone else reporting the same issue here – replaced the OEM mag release with a WC mag release; tested both the WC mags and GI mags – both can now be inserted without issue.
    2. This is more of a non-issue for me but has been an issue for some folks. The grip panel bushings have been said to be “off” and will not accept non-OEM screws. I had no problem using the screws provided to me by Coolhandgear.com to install their grips. I tried two sets of differing screws and had no issues.
  6. I’m absolutely loving this gun. My target gun was a Springfield Armory but I had a very difficult time deciding exactly what I wanted and then had a difficult time finding them in stock. So, I did research and decided to try the SDS 1911s. This gun hits way above it’s weight…it is very much comparable to a Springfield Armory Garrison (but railed). The B45R was well under $500, but has a forged frame (what other non-GI 1911s are in this price range that offer both forged frames and slides?). I basically stole a great 1911. I also don’t have any issues buying foreign/Turkish guns. I’m a 10 year military combat veteran, so I’m as patriotic as any self-proclaimed patriot, and have probably sacrificed more. ALL of my 1911s are non-US and I’ve Caniks and Tristars as well, one being my CC gun. I’ve no problem with any non-US-made guns.
  7. The plan is to maybe change/fit a silver barrel bushing but maybe in 6 months or so.

UPDATE 2:

  1. I visited the range tonight and put more rounds through the 1911 – 169 rounds to be exact. 150 of that was PMC Bronze FMJ and 19 was Remington HTP 185-gr JHP. There’s now a total of 319 rounds through the gun.
  2. One JHP failed to feed but the gun is very dirty now (haven’t cleaned it since the day I received it). As well, it choked when using one of the three GI mags I bought – the round was the first in the mag. No, 19 JHP rounds isn’t much but good JHP 45ACP ammo isn’t exactly cheap, so that’s going to have to suffice for now.
  3. I decided to test it at 12 yards out. I usually don’t shoot at distances longer than 12 yards. The gun is accurate, even in my hands (although there were flyers).
  4. The gun is tearing up my hand at the beavertail – still trying to determine how. I’m being pinched badly at the webbing of my hand where the two skin textures meet. I’ll use gloves the next range visit. UPDATE: I believe it is the back of the right-side (ambi) safety that is rubbing my hand raw. It isn’t sharp but isn’t rounded either…over long periods of time, it’s an issue. I may look into getting a one-sided safety.
  5. I’ve a Wilson Combat magazine release on the way. That should fix mag insertion problem with the WC and GI mags. No longer an issue.

UPDATE 3:

  1. I’ve shot 429 rounds from my SDS Imports DB45R 1911, thus far. Since I’ve been curious about it’s carry capabilities, I’ve been trying to shoot JHP from it, initially with mixed results.
  2. I initially shot Remington HTP 185-gr JHP, which generated several failures to feed (FTFs).
  3. Federal LE 185-gr JHP was used, as well (maybe 25 rounds), which also generated some FTFs.
  4. International Cartridge Corporation’s (ICC) 45ACP 155-gr frangible hollow points were used. For the most part, these shot without issue. That ammo can be used as defense ammo.
  5. I also fired 20 rounds of Underwood ($$$) 45ACP +P 230-gr JHP. 8 of the 20 rounds generated FTFs. I used Wilson Combat mags with this ammo. Since this ammo is expensive and since it generated so many FTFs, I will stop shooting that ammo through the DB45R. Once I suspect that the gun will shoot it without FTFs, I’ll test the ammo again.
  6. Inceptor ARX 118-gr defense ammo (non-JHP) was used, using the WC mag. There were no FTFs.
  7. I shot PMC Bronze 185-gr JHP (non-SD ammo), using the WC mag.. There were no FTFs.
  8. Hornady Critical Defense 185-gr JHP was shot through the gun, using the WC mag.. There were no FTFs.
  9. So, I now know that I can use the following ammo as viable ammo for self defense:
    ICC 155-gr FJHP
    Inceptor ARX 118-gr
    PMC Bronze 185-gr JHP
    Hornady Critical Defense 185-gr JHP
  10. In my view, the ammo problems are more than likely due to projectile ogive dimensions as well as hollow point size. If it were an issue with the gun, ALL the JHP I tested would be generating FTFs. There are no specification standards on ogive or projectile dimensions in today’s ammo market, so it’s difficult to make a gun 100% reliably eat all mass-produced ammo, and 1911s aren’t Glocks, so….

I plan to continue to shoot the PMC Bronze JHP ammo as range ammo, to continue the break-in process of the DB45R 1911.

Categories
Bul Armory fail to feed FMJ FTF range report SAS II Ultralight

SAS II UL Range and Progress Report for 10/2023

I’m currently very near to crossing over the 1,000 round threshold with the Bul Armory SAS II Ultralight.

I visited the range a few days ago, bringing 200 rounds of ammo. I ran out of range time before I was able to shoot it all. I visited after work since I’ve to be at work every Wednesday now. I may make this my range day every Wednesday since my work isn’t far from XCal.

While I was waiting in line for a lane assignment, I happened to see some of the range’s rental selection. They’ve Staccatos, as well as several really nice 1911s. What I really want is to try the G43X and G48 (I may be purchasing one of those next year). I didn’t see those guns in their rental section but their rental section is very large and I’m sure they’ve a good selection of Glock rentals. I’ll check next time I go. I also wanted to try their P365, since I’ve seen more than one person asking, “Why buy a SAS II UL when a P365 is better?” In my opinion, that’s a rather lame comment since most folks aren’t cross-shopping those two guns (due to price as well as platform — both of those being quite different frome one another). Yeah, a P365 will conceal better, but P365s are also more difficult to shoot quickly and accurately. The SAS II UL has a bigger grip than the P365, but that doesn’t mean that an owner will have issues concealing a UL. The UL will almost certainly be less snappy and quicker to shoot. It’ll probably outshoot the G43X, too.

I shot 187 rounds of the 200 that I broght with me. Most of it was Fiocchi 115-gr FMJ, although some of it was Blazer 124-gr FMJ and Remington 124-gr FMJ. That puts me at 986 rounds through the SAS II UL, thus far.

I had 6 fails to feed (FTF) prior to the pistol course I attended a few weeks ago. I had one FTF during that class and one at the range visit this week. The total FTF count is now 8. 8 of 986 is 0.81 — that is the current failure rate in percentage.

The prior percenage was 0.96, with 6 fails at 623 rounds (back in May 9, 2023). I had several range visits where I didn’t have any failures. This could be due to me learning how to better grip this handgun, as well as me not shooting as much JHP (which tends to be high pressured, which may induce limp-wristing).

Why do I report this as a percentage? So many folks look at failure counts as hard numbers. They want it to be zero. In my opinion, to expect no failures is an impossible ask. Sooner or later, a gun will fail, especially since failures can be induced by the shooter, as well as out-of-spec ammo. Some ammo will be in-spec but will have large hollowpoint projectiles (which do not meet a specification). I don’t think it is logical to expect a handgun to meet every single variation of ammo specification, as well as account for owner-induced failures. So, I post the round count and count of failures and then convert both to a percentage. Percentages have better meaning, IMO. It tells a better story than a raw number of failures.

I still need to purchase the targets that were used in the pistol course I attended (as well as the target stickers).

I’ll post some range footage as soon as I’ve cropped a few sections for viewing. I mainly shot at 7 and 10 yards, some at somewhat fast paces. I also tried to practice accuracy. I shot several times at 15 yards, too. I’m still struggling with grip. I keep readjusting my weak hand after a shot — I need to find a better way to stop doing this. I’m subconsciously doing that.

Categories
1911 2011 AF1911-S15 Alpha Foxtrot ammo Bul Armory defensive ammo SAS II Ultralight training

Another 1911 Range Visit / Upcoming Training

Once again, I took the Alpha Foxtrot S15 to the range, as it exhibited some failures during my last range visit, which I believe I documented on this blog.

I also forced myself to shoot the SAS II UL this go-around, since I’ve been neglecting the gun (and I’m also carrying it).

I brought some of my open boxed SD ammo to test the S15, as I initially thought it was having issues due to bad ammo. Another culprit could have been the mag (there was one magazine in particular that was having issues). Another culprit could have been me – I’d shot the gun toward the end of the visit and I was probably getting tired (hand/wrist/arm fatigue).

Right off the bat, I got two fails to feed, with the suspect mag (I’ve marked it). I ended up stopping everything, emptying the mag of ammo, and putting the ammo in a different magazine. The failures stopped.

I’m thinking I might ask Shield Arms to replace this mag. The mag is new and should be covered by manufacturer’s warranty. It’s odd that the failures don’t always occur, though. The ammo it was choking on was Sig Sauer V-Crown 147-gr JHP.

It also failed once when shooting Remington Golden Saber 147-gr JHP. It ate 21 other Golden Sabers without issue, though.

Those were the only failures, so it wasn’t really all that bad this time around.

I’m at 623 rounds through the S15 now. The gun is uncannily accurate. It doesn’t seen to be as snappy as the SAS II UL, but it has better grip surfaces (by far). Now that I know that it’ll eat JHP without issue, and now that I’ve tested the mags, I can actually consider carrying this gun now, although I’ll keep testing it (I’m still wanting to carry the SAS II UL, too).

I’m at 661 rounds through the SAS II now. I shot 38 rounds tonight, all Herters Target 115-gr FMJ. There were no hiccups or failures. I shot all the ammo at 10 yards, quickly (since I’ve the optic installed).

I’ll be working on posting range video footage this weekend, of both guns. I have footage from the last visit but the settings were out of whack and the field of view wasn’t the best (the framing was off-center, as well).

Next week, I’ll be attending my first handgun course. The plan is to use my current carry gun (SAS II UL). I’ll be bringing my Glock 19 as a backup gun, in case they state my SAS II is too small and in case the SAS II has a breakage. I’ve other guns I can consider as backup guns but most of my guns are DA/SA and I’m more used to SAO nowadays. I’ve several striker fired duty- and compact-sized guns but I’ve no holsters for them (nor extra mags). At this point in time, the Glock 19 is my best option (I’ve extra mags and several holsters for it).

I plan to shoot Blazer 124-gr FMJ for the course (was told that I’d need 200 rounds, so I’ll buy 4 boxes of 50). Blazer is reliable for me, but so is the Herters Target, so I may buy that brand instead, although the Blazer is just a few dollars more.

I was planning on a rifle course too, but I need the time to purchase mags and magazine pouches that’ll fit my carry belt. I may have to wait until next year for that, although I can also take a rifle course by XCal. We’ll see.

Categories
9mm AF1911-S15 Alpha Foxtrot Grand Power limp-wrist P11

Summary of Range Session – 9/8/2023

I went to the range tonight because I wanted to work off some steam (been busy with work and have been stressing).

I’d been thinking about my Grand Power and recently had someone reach out to me on YouTube. She said that she has the P11 and that she’d been having the exact same issue (fails to return to battery, or FRTB), but that her husband didn’t have the issues when shooting it. She hinted that it may’ve been limp wristing that caused it.

I did a bit of research and it seems that limp wristing can cause FRTBs.

I never realized that I could’ve been limp wristing the gun. It is rather slick, with no significant texturing on the grip.

I decided to begin taking it to the range to see if I can shoot it without experiencing the FRTBs. I shot 50 (well, 48) rounds of Koenig 110-gr JHP Match through it tonight and I didn’t have any failures. Note that the gun is configured a bit differently since I last shot it — I’m using a small Hogue rubber grooved slip-on grip, which helped with getting control of the handgun. I was ensuring I had a strong grip on the gun. I’ll continue to bring it to the range, shooting 50-100 rounds from it when I can, and trying to practice good grip technique so that I’m accurate as well as not limp-wristing.

I also shot 155 rounds from the Alpha Foxtrot S15 1911. The ammo of the night for that gun was Herters Target 115-gr FMJ with a splash of Fiocchi 115-gr FMJ. Whereas I didn’t have any issues last range visit, I had 8 FTEs this range visit. I shot the same ammo last visit, as well.

The issues could be (possible solutions are below, in italics):

Bad magazine – I shot with all six mags and only one mag generated failures, so I kept shooting with it to see if I was limp-wristing and causing the failures. I shot many rounds through that mag tonight and there was only one time where I got thorugh a mag without failures. I marked the mag and will put it aside. The plan is to use the other mags next range visit – if the failures stop, then I’ll know that the mag is the problem.

Bad box of ammo – I bought 200 rounds of Herters (2 x 100-round boxes). I got through one box with only two fails to extract. The other box had five FTEs. The Fiocchi had one failure – not only did it the spent case not extract, but it was still fully in the chamber, and the slide did not lock back (it was the last round of the mag). Also, I noticed that the slide would sometimes seem to be moving a bit slower than normal after a round is fired, which is usually indicative of inconsistent amounts of powder within the case. As well, some of the ammo looked funky where the case crimps onto the projectile, as if the ammo had possible QC issues. I’ll bring some good JHP with me next range visit, to see if the issues still occur with good ammo.

Limp-wristing – I won’t count this out, since the FTEs started occurring mid session of my range visit. I tend to fatigue myself as I practice (this is normal). Next range visit, I’ll test the S15 (and the other 5 mags that didn’t have issues) before shooting any other guns.

I did have fun shooting the Grand Power again. I was accurate with it. I shot it once at 10 yards but the spread was wider than when I shoot the S15 at that range, which I initially thought was odd until I realized that the S15 has far better grip texturing. I ended up sticking with shooting at 7 yards.

The S15 is accurate AF! I spent a large amount of time shooting at 10 yards and was accurate. Not only that, there were times where I was shooting pretty fast and my groups were tight as I shot further out. And that was with irons. This gun is uncanny, but it’s really because of the front checkering on the grip. It’s going to seriously spoil me. I’m already thinking about selling all my other 1911s so that I can focus on 1911s and 2011s that have front checkering. Yes, I can get checkering added to my existing 1911s, but some gunsmiths won’t touch non-US guns and all guns that get checkering will need to be repainted/refinished.

I also now have just under 500 rounds through the S15. I’m slowly accumulating the round count on this gun. I’ve just under 1600 rounds through the GP P11.

Categories
Bul Armory Optic range report SAS II Ultralight video

Four Week Review of the Bul Armory SAS II UL

This is just a video-captured 20 minute summary of my experiences with the SAS II UL.

Categories
1911 2011 Bul Armory handguns range visit SAS II Ultralight

SAS II UL Optics Adjustment Issues – The Wedge Was Not Needed!

My range notes for today’s range visit:

This is the first time I’ve tried a range other than Elite. Elite closed last weekend, so today I visited XCal in Ashburn (30 min drive – 30 miles).

Shot 48 rounds of Norma 115-grain FMJ. There were no fails.

I also shot 64 rounds of Fiocchi 115-gr FMJ. There were no fails.

Total rounds this session was 112 rounds of FMJ. There were no fails.

I spent a majority of the 1-hour session adjusting my new optic (Holosun HS507K-X2 ACSS). It was initially frustrating because I couldn’t hit point of aim at all. I kept adjusting the sight and was able to get proper windage but couldn’t get the proper elevation…no matter how much I tried, I couldn’t get the dot lower than 6-8″ above the bulls-eys when shooting at 10 yards.

I finally stopped and decided to remove the optic wedge I’d installed (was supposed to fix an issue with the SAS II UL having elevation issues when an optic is mounted). Once I removed the wedge, I reinstalled the optic and was immediately hitting the bulls-eye. It still needs to be fine-tuned, but I’m quite happy with the functionality of the optic and that I solved the elevation issue!

I bought a crapload of ammo, but only got to shoot 112 rounds, since I was attempting to adjust the optic’s point of aim and since I had the issue with elevation.

I wish I’d shot a bit more to break the 500 round count.

I’ll attempt to visit again next week. I’m probably going to apply for membership before then.

I almost decided to put the irons back on tonight, at the range. The only thing that stopped me was that I’d forgotten to bring the irons with me. That forced me to bird-dog the issue – I didn’t need that optic wedge I’d installed and I shouldn’t have immediately installed it. That’s what I get for believing an internet source – bottom line is, don’t believe everything you read on the internet! Trust but verify. If I’d have installed just the optic and not the optic wedge, I’d have not had an issue at all.

Before removing the optic wedge

After removing the optic wedge
Categories
ammo Bul Armory defensive ammo range report range visit SAS II Ultralight

Summary of the SAS II UL’s 2nd Range Visit

I went to the range yesterday and shot approximately 160 rounds of ammo. Half of it was FMJ and the other half was straight-up SD ammo (none of the cheap stuff).

Some quick observations:

  • I cleaned the firearm for the first time today (a day after the 2nd range visit). It was filthy. I could see preservative oil in the upper reaches of the slide (looked like rust but I know it wasn’t – tell-tale sign of preservative oil). I didn’t deep-clean the gun – I only field-stripped the gun, but I did remove the firing pin and clean it (I didn’t have any pipe cleaners, so I didn’t clean inside the channel). I also cleaned the extractor claw (did not remove the extractor, though). The claw was nasty. The barrel was nasty and had some crud in the chamber that took some time cleaning.
  • I took the opportunity to also take apart the two mags that came with the gun. I cleaned and oiled them (light coat of oil).
  • I noticed that the rear sight was loose. I’ll need to remove the rear sight, clean the threads, and then use blue thread locker to secure it, but for now, I just tightened the rear sight screws – I’ve an optic on the way here, and I’ll be removing the rear sight anyways.
  • I received two more OEM mags today, as well as a flat trigger shoe. I thought I could quickly install the new trigger shoe – nope…I need a 1.3mm allen wrench to remove the trigger shoe. That’s going to be a bitch to get off, too – it will take time, IF it’s not secured with threadlocker. If it is, it’ll take even more time.
  • I also received two optic shims (I only needed one but I wanted redundancy). The HS507K will require the shim, otherwise I won’t be able to adjust it properly (this is a known issue with the 507K and the SAS II UL).
  • The gun fired OK during the range visit. I shot the following ammo: Herter’s Defense in 115-gr JHP, Sig V-Crown Elite Defense 124-gr JHP, Koenig Competition 110-gr JHP, Remington Golden Saber 124-gr BJHP and 147-gr BJHP, and Hevi Duty 100-gr frangible flat-nosed ammo. I also brought some Fiocchi 115-gr FMJ ammo.
  • I had two fails to feed (FTF) with the Sig ammo, one of the FTFs being a double-feed. This ammo shot a tad bit high.
  • I had two FTFs with the Koenig ammo – same deal, one of the FTFs being a double-feed. As well, this ammo shot 2-3″ high! To hit the bullseye, I had to aim 2+ inches low.
  • I had no failures with the rest of the ammo, although the Hevi Duty frangible ammo shot high.

Basically, it seems that any light-for-caliber ammo that is shot from this gun will land high. That was my experience with Inceptor ARX (65-gr fluted tip) too.

So, we’ve shot a total of 336 rounds of ammo from the SAS II UL, thus far.

I still need to master the trigger of this gun. It’s a bit more difficult to shoot (and be precise) than my other 1911 9mm handguns, part of the issue being recoil management. I’ll get better as I spend time with the gun.

Categories
7.62 x 39 AK AK-47 AK-P Arsenal Canik PSA SAM7UF-85 TP9 Elite TP9 Elite Subcompact

AK Range Day!

Today’s range day was deemed AK range day!

I took out the Arsenal SAM7UF and PSA AK-P. The former is a milled rifle that I’ve owned 2-3 years but never shot until today. The latter is an AK pistol that I bought 3-4 years ago and have been shooting off and on.

Both are dreams to shoot. I’ve no range footage because I hate recording when shooting long guns (my mounting point doesn’t agree with the rifle shooting position).

I shot the SAM7UF first. I thought it would be hard on my shoulder but it was rather mild, especially considering that the folding stock’s makeup is usually something that folks complain about. It’s supposedly not easy to shoot, but the stock didn’t bother me (I’ve the rails covered with paracord).

I thought the recoil would bother my shoulder with that stock but much of the recoil never made it to my body. The milled rifle is heavy and the heft absorbed much of the recoil.

I shot out to 25 yards. I wasn’t hitting point of aim but I think it’s because the rifle may be zero’d to 100 yards. I need to study the method of zeroing AKs. When I do, I’ll revisit the range with the SAM7 and zero the gun (on the 25 yard range, since I’ll have a difficult time seeing further than that).

The gun has some blast, too. It seems it has more blast than my other long AK (a bastardized AK-63D from Classic Firearms). I shot 30 rounds before I switched to the PSA AK-P.

The PSA AK-P is a flamethrower but I already knew that. I didn’t feel like squinting trying to hit 25 yard targets so I moved the target closer, to half that distance.

I’ve a red dot sight for this firearm but I removed it when I last took it out, as I hated it. I’m decently accurate with the iron sights, so I shot 30 rounds at one of those target papers that have 5 targets on it. all but maybe 4-5 landed on paper (because the targets on the edge of the paper don’t leave much room for error and I was doing a lot of quasi double-tapping). The groupings were pretty tight for the rate of fire I used. I also shot while standing. A picture is below.

12 yards, standing w/ irons…

The gun bucks and throws fire. Additionally, it got HOT! I burned myself once and had to wrap it up in rags before I put it in it’s case so it wouldn’t melt the inside foam. Also, keep in mind that this is a pistol and the brace is HARD on a shoulder with the kick of an AK pistol. I also tend to pull the gun in really tight while gripping the mag. I’ll be bruised tomorrow.

Lastly, I always try to shoot my carry gun when I’m visiting the range, so I shot some defensive ammo from the Canik TP9 Elite SC. This ammo is something new to me, but I bought a batch of it from my range 2 nights ago, since it was on sale at 19.99 for a box of 50. The make and model is Federal 115-gr Hi-Shok JHP. I bought 250 rounds of it, not knowing if it was good or not but liking the sub-$20/box price. I later researched the ammo and found that the ammo is GOOD and that law enforcement uses it. I’d assumed that since the box was white and since the ammo wasn’t being sold in 20-round boxes, it was range ammo. It is not. So, tonight I bought 100 more rounds of it just to shoot with tonight. It shot well, without hiccups, and without feed or extraction issues. I may end up trying to buy it in bulk but my research shows that when looking for it online, the low price is 0.49/round, which is a bit high compared to what I found at my range. My range will carry it until it runs out and won’t let me buy in bulk anymore (the person that sold it to me apparently shouldn’t have let me buy so much without shooting – I bought it after my shooting session).

Right now, I’m right at 482 rounds shot through the TP9 ESC. Expect that number to go quickly as I continue to practice with it.

The AK-P currently has 370 rounds through it. I could shoot it more but for some reason, shooting that gun indoors gets old quickly (it has tremendous blast). I looked at the internals (trunion, bolt, and bolt carrier) and the parts aren’t beat up (this model is a GF3). Most AK snobs hate US-made AK, and think they’re sub-par. If I have any issues, it’ll be something like fire-pin issues, or something stuck in the firing pin channel (primer metal), or maybe a loose firing pin retaining pin (which probably won’t be an issue, as I’ve checked it and it is not loose at all). I will probably buy another firing pin, in case the OEM one breaks.

The SAM7UF only has 30 rounds through it but I’ll try to shoot it more, now that it’s no longer virgin.

Categories
1911 1911A1 45ACP 9mm American Classic Commander Metro Arms RIA Rock Island Armory

New YouTube Video – 1911 Range Day!

I tried a new format in this video, using my GoPro hat-clip. What I didnt’ account for was the volume isn’t crisp, as the hat-clip requires usage of the GoPro case, which is apparently covering the camera’s mic. 🙁

There were issues with the Metro Arms 1911. I’ve been suspecting as much the past 1-2 years, but my handgun experience is expanding and I’m confident to say that this handgun has issues with it’s sights. I’ll be looking into obtaining a new set of sights for this handgun (I wouldn’t mind having the sights that are on my RIA Tac Ultra installed on this handgun).

Also, I finally installed the 9mm barrel into my RIA Tac Ultra (I have always shot it with the 22TCM barrel installed). I shot 140 rounds of 9mm from the gun. The gun now has a total of 746 rounds through it. It’s my third most-fired handgun (the Grand Power P11 and Bersa Thunder Plus are 1st and 2nd).

There were some fails to feed when firing the Tac Ultra, but the feed issues only occurred with the OEM mags. I’ve Wilson Combat 9mm ETM mags, which didn’t have any feed issues. I also used the 38 Super mag that came with the Tac Ultra. I also used the 9mm mag that came with my RIA Rock Ultra. The latter two mag are the mags that had inconsistent issues. The feed issues were occurring mid-mag.

Lastly, I need to research who is the new US importer for Metro Arms. Eagle Imports was the importer, but they went out of business earlier this year.