I wanted a place to discuss my handguns and firearms in general. Everyone seemingly has lots to say about guns, so I promise you this won't be a rant blog.
I took the Prodigy DS Compact to the range today and brought 150 rounds. The Prodigy ate all of it without issue – no fails (was Magtech 115gr FMJ). There are now 270 flawless rounds through the gun.
A Cyelee CAT is mounted to the DS. These are two mags of some good groups (for me and this particular gun).
I still don’t like the trigger, but I may have adapted to it (or learned to ignore what I don’t like about it). I’ve also been working on my support hand grip. Yeah, my support thumb isn’t glued to the gun – I’m fine with that, as THM says that doesn’t matter…what matters is that other portions of the support hand being glued to the grip. I noticed that I didn’t figet with my support hand as I normally do. Also, my strong side thumb isn’t resting on the thumb safety. My thumb does not like sitting up there (I’ve developing arthritis)., so I let it sit wherever it’s comfortable…I’m OK with that.
I’m shooting at orange 1″ pasties at 10 yards. My goal was to try to stack the rounds. I also challenged myself by trying to shoot at a decent pace. The first mag, I was shooting at the top orange pasty. The second mag, I was shooting at the left-side pasty. I was quite surprised, especially as it was toward the end of the range session, when I typically tire and start shooting badly.
UPDATE (4/25/2025):I did a detail strip of the Prodigy DS Compact yesterday, to check which parts were MIM, but also compared the sear spring with an EGW sear spring for Commander-size 1911s. The EGW was a tad taller and would not fit in the gun – I know, I tried – it didn’t work. I then looked at and very slightly tweaked the middle tine of the sear spring and then put the gun back together. When I did a function check, I immediately noticed that the weight of the trigger was less – the trigger wall didn’t see as bad as before. I checked the trigger weight via Lyman’s gauge…it’s at 3 lb 2 oz now. It dropped a full pound. It feels GOOD! I’ll be visiting the range tomorrow (at 10 PM) to test it and put more rounds through the Prodigy. I want to be at 500 within the next 7 days (I’m at 260 now).
The gun is beautiful. I’m not just saying that or trying to justify a purchase. It’s actually a gorgeous gun, a gun that feels really good in the hand, has good fitment and finish, and is a greate shooter.
I shot it for an hour, maybe an half hour after I did the background checks. I shot 160-ish rounds from it. Because I immediately shot it, I couldn’t clean it and it was barely lubed (I could only lube the rear rail inserts. Because of that, it failed to return to battery maybe 3-4 times, but that could’ve also been due to the fact that the included Glock mags have tired springs – they’ve hardly any resistance and stopped locking back the slide after the last rounds. I’ve four new G17 mags and will use them from now on – it’s not worth replacing the springs, as the springs are $8 and with shipping fees, they’ll be close to a new mag in price.
You know what? I’ve talked about the gun in a video I posted on YouTube, so I’ll just share that video here.
And, some range footage showing the accuracy of the gun.
I went to the range maybe two weeks ago and my main goal was to dial in the sights on a particular 1911. Instead of spending a significant amount of range time zero’ing the gun, what I’d been doing was shooting 1-2 mags every range visit, bringing the targets home, and making sight adjustments at home. I’d then bring the gun when next visiting the range and testing the sights to determine if further adjustments were necessary. I did this maybe 3 times before I was satisfied.
Why not just spend a whole range session to do this? I’ve other guns that I want to shoot (to work out similar issues in adjustment)…timesharing guns can sometimes be problematic and I don’t have my own range or know of anyone that does.
The below video highlights the culmination of properly adjusting the sights on this gun.
The gun is a Rock Island Armory Tac Ultra MS with the 9mm barrel (it came with two). I’ve never shot this gun well, accuracy-wise, and I’d thought it was due to it being bushing-barreled. I’ve another RIA MS 9mm gun and it is bull-barreled – that gun is a low-effort gun as far as accuracy is concerned. I’ve always been accurate with that gun and I always thought it was mainly due to the bull barrel.
Both of those guns lack front strap checkering, and I sometimes struggle with maintaining a proper grip on those two guns. I added a strip of Talon Grips tape on each on their front straps. I think that is why I had such a great session with the Tac Ultra.
Note that I’m shooting at 15 yards, at 2″ sticky bullseyes. I could barely see those sticky targets at that range, but tried to just aim as best I could and tried to maintain proper grip and trigger discipline. I think it worked out well!
I recently started using a weapon-mounted light (WML), carrying it on my Bul Armory SAS II Ultralight. I lost it when I took the gun to the range for practice – it fell off while I was shooting. I did not become aware that the light was missing until almost 2 weeks later!
There are some things to remember and prepare for when usually WMLs.
WMLs usually require a holster that keys off the light. If you lose the light, you’ll be unable to properly carry the gun if you only have a holster that requires a WML. I didn’t notice that the light was gone – it still fit into the holster but the fit wasn’t proper. I’ve no idea why I didn’t notice it intially. The only reason I noticed that the light was gone was because I removed the gun from the holster to check the light and it wasn’t on the gun.
If you lose a light, you should be prepared by either having a backup light or a holster that will allow you use without a WML. In my case, I just pivoted back to using the Tenicor Certum 3, but I was irritated that I’d lost a $100 light and irritated that I had to go back to the Certum, as I’d just started using the QVO Tactical holster.
Also, a good thing to do would be to check your lane/booth before leaving, to ensure that you’re not leaving equipment. I always check and I did check that night but didn’t see the light in the booth (it fell forward of the firing line and was lying on the ground), so a good check would be to ensure that your light is still mounted to your gun before you leave the range.
I contacted my range and shared with them that I’d lost the light at the range and provided them the lane I was using, the make and model of the light, and the date/time I was at the range. I also posted about losing the light on Reddit. Someone replied to the Reddit post stating that they saw the light immediately after I’d left the range (it fell forward of the firing line and was lying on the ground). He said he reported it to the range officer and asked the range officer to retrieve it. He told me to contact the range and ask for Andy.
I contacted the range via their web page and they looked at the camera footage and stated that they couldn’t see the light on my gun and didn’t even know if they were looking at the correct lane. I told them what I was wearing and what I was shooting and told them that the light may’ve come off the gun very soon after shooting it and to not rely on the footage. I told them that I’d checked the lane before leaving and that the light almost certainly fell past the firing line. I also told him that another person on Reddit said that he’d seen the light and had reported it to the RSO and that he’d watched the RSO retrieve it. It was actually a bit surprising that I had to tell them that to get them to become more engaged – it was almost as if they weren’t convinced I’d lost the light at their facility.
The next day, I got a call (I was away from the phone, so a voicemail was left). A supervisor said they’ve my light but that the RSO (Andy) had forgotten it in his range pouch and taken it home. Andy is a college student and was working minimal hours, so he wouldn’t be available to work until 3 days later. He told me to come on on Friday after 3 PM and the light would be available for me to pick up.
I went and picked it up yesterday. They said they’d a few lights (this most be a common issue) and asked for the make/model. They gave me what looked like my light but they must’ve had several TLR-7X lights and I think I received the wrong one. Why do I think that? Because, when I got home and was trying to install the light and it wouldn’t fit. With mine, I didn’t have to change the key – the light fit on the gun with the key that was already on the light. When I got this particular light home, it would not fit on the gun at all. The key was the same (the Universal 1 key) but I think the TLR-7s are packaged with different keys and are built for particular gun types/models. Since I had other keys, I tried those and was able to use a 1913 key that fit the gun (I forgot which one I used).
How do you keep your Streamlight TLR-7 from coming off the gun? They come with e-clips. After selecting a key and installing it, you install the e-clip to the retention screw, which keeps the screw from loosening. I’ve heard many guys on Reddit stating that they don’t use the e-clip. That’s a bad decision, as you’re only supposed to hand-tighten the retention screw. The light comes with two e-clips and you’ve to install it once you’ve chosen the correct key to use. I didn’t install the e-clip because I was unaware that it was 100% necessary. The e-clip is on now, though.
I’m not sure if I should’ve just went back to the range and told them that even though they gave me a TLR-7X, they gave me someone else’s. It may’ve taken weeks and I may not have ever gotten the correct light, so I settled for this.
UPDATE:
I’ve pieced together what happened with my light.
When it was returned to me, it wouldn’t fit on my gun. It fit on my gun before I lost it. I had to change out the key before the light would fit on my gun again. This means someone changed it.
As well, I’d never enabled strobing on the light – this is something that you can’t do by accident, as it requires pressing the “on” button consecutively, ten times…that enables strobing. Someone else had to have done that.
Initially, I’d thought that I had the wrong light, which accounted for why the light wouldn’t fit my gun and why strobing was enabled. I found a picture from before I’d lost the light and that pic had captured the light’s serial number. I compared that with the serial number on the light after it was returned to me. The serial numbers match, meaning the light is the one I had before I lost it. This means that whoever had my light while it was lost was actively using it (ie, it didn’t stay lost, but was taken/used after it was found by someone else).
The RSO that retrieved the light may’ve been using it, and that is sad.
By nature, I always am overly trusting. I mean, I didn’t do anything wrong and didn’t do anything that suggested I was naive. I still feel wronged, though. I grew up less-than-rich. I wasn’t poor, but I wasn’t far from it. I know the value of money. I make great money now but no matter the amount, it’s hard-earned. Gun lights aren’t exactly cheap – mine wasn’t top-of-the-line, but it wasn’t cheap. I’m not a person to just blow off losing a $100 bill and that light was more than $100. I got it back, yes, but not before someone attempted to use and alter it. That’s fucking sad.
I’ve been keeping a running tally of notes after visiting the range – keep in mind that I’ve not been to the range with this particular gun in quite a while (2022). Here’s the latest version of my notes:
UPDATE 1:
Range photos with detailed captions are at https://photos.app.goo.gl/yrLbWQNMmDjgJCzV8. Note: I’m not sure if Reddit will choke on Google’s URL shortener – I’ve had problems with it in the past.
I brought 2 Wilson Combat mags with me, the two that the gun came with, and 1 ACT mag from another 1911. The ACT mag choked the gun once, and I knew it would be problematic because it’s been acting up the last few range visits (ie, it wasn’t an ammo issue). I bought another WC mag from the range store – it will replace the ACT mag. I will keep the ACT mag in case I need to scavenge parts from it.
The B45R loved PMC Bronze 230-gr FMJ and I shot 50 rounds of it (this ammo always feels peppy). The other ammo I used was International 155-gr frangible ammo. That ammo is crappy but it never choked the B45R. My Metro Arms hates it. I also noticed slide slowdown (an indication of low powder charge) but only when shooting it out of the Metro Arms…I didn’t notice any of that with the B45R. I shot 100 rounds of the International ammo.
I bought some G10 grips to replace the cheap-feeling grips that came with the gun. They work very well, and I expected nothing less (all of my other 1911s are using G10s).
Issues:
The WC mags will sometimes hang up in the mag well. It seems that the magazine catch/release is blocking insertion. If I hammer up on the mag, it blasts past but smacks into the upper portion of the gun (that’s probably not a good thing). If I actuate the release button a tad, the mag is allowed past. I’m hoping this issue will go away. This only happens with the WC mags. I’ve three 7-round Mecgar mags on the way here and they should arrive tomorrow. I’ll see if those get hung up. UPDATE:Found someone else reporting the same issue here – replaced the OEM mag release with a WC mag release; tested both the WC mags and GI mags – both can now be inserted without issue.
This is more of a non-issue for me but has been an issue for some folks. The grip panel bushings have been said to be “off” and will not accept non-OEM screws. I had no problem using the screws provided to me by Coolhandgear.com to install their grips. I tried two sets of differing screws and had no issues.
I’m absolutely loving this gun. My target gun was a Springfield Armory but I had a very difficult time deciding exactly what I wanted and then had a difficult time finding them in stock. So, I did research and decided to try the SDS 1911s. This gun hits way above it’s weight…it is very much comparable to a Springfield Armory Garrison (but railed). The B45R was well under $500, but has a forged frame (what other non-GI 1911s are in this price range that offer both forged frames and slides?). I basically stole a great 1911. I also don’t have any issues buying foreign/Turkish guns. I’m a 10 year military combat veteran, so I’m as patriotic as any self-proclaimed patriot, and have probably sacrificed more. ALL of my 1911s are non-US and I’ve Caniks and Tristars as well, one being my CC gun. I’ve no problem with any non-US-made guns.
The plan is to maybe change/fit a silver barrel bushing but maybe in 6 months or so.
UPDATE 2:
I visited the range tonight and put more rounds through the 1911 – 169 rounds to be exact. 150 of that was PMC Bronze FMJ and 19 was Remington HTP 185-gr JHP. There’s now a total of 319 rounds through the gun.
One JHP failed to feed but the gun is very dirty now (haven’t cleaned it since the day I received it). As well, it choked when using one of the three GI mags I bought – the round was the first in the mag. No, 19 JHP rounds isn’t much but good JHP 45ACP ammo isn’t exactly cheap, so that’s going to have to suffice for now.
I decided to test it at 12 yards out. I usually don’t shoot at distances longer than 12 yards. The gun is accurate, even in my hands (although there were flyers).
The gun is tearing up my hand at the beavertail – still trying to determine how. I’m being pinched badly at the webbing of my hand where the two skin textures meet. I’ll use gloves the next range visit. UPDATE: I believe it is the back of the right-side (ambi) safety that is rubbing my hand raw. It isn’t sharp but isn’t rounded either…over long periods of time, it’s an issue. I may look into getting a one-sided safety.
I’ve a Wilson Combat magazine release on the way. That should fix mag insertion problem with the WC and GI mags. No longer an issue.
UPDATE 3:
I’ve shot 429 rounds from my SDS Imports DB45R 1911, thus far. Since I’ve been curious about it’s carry capabilities, I’ve been trying to shoot JHP from it, initially with mixed results.
I initially shot Remington HTP 185-gr JHP, which generated several failures to feed (FTFs).
Federal LE 185-gr JHP was used, as well (maybe 25 rounds), which also generated some FTFs.
International Cartridge Corporation’s (ICC) 45ACP 155-gr frangible hollow points were used. For the most part, these shot without issue. That ammo can be used as defense ammo.
I also fired 20 rounds of Underwood ($$$) 45ACP +P 230-gr JHP. 8 of the 20 rounds generated FTFs. I used Wilson Combat mags with this ammo. Since this ammo is expensive and since it generated so many FTFs, I will stop shooting that ammo through the DB45R. Once I suspect that the gun will shoot it without FTFs, I’ll test the ammo again.
Inceptor ARX 118-gr defense ammo (non-JHP) was used, using the WC mag. There were no FTFs.
I shot PMC Bronze 185-gr JHP (non-SD ammo), using the WC mag.. There were no FTFs.
Hornady Critical Defense 185-gr JHP was shot through the gun, using the WC mag.. There were no FTFs.
So, I now know that I can use the following ammo as viable ammo for self defense: ICC 155-gr FJHP Inceptor ARX 118-gr PMC Bronze 185-gr JHP Hornady Critical Defense 185-gr JHP
In my view, the ammo problems are more than likely due to projectile ogive dimensions as well as hollow point size. If it were an issue with the gun, ALL the JHP I tested would be generating FTFs. There are no specification standards on ogive or projectile dimensions in today’s ammo market, so it’s difficult to make a gun 100% reliably eat all mass-produced ammo, and 1911s aren’t Glocks, so….
I plan to continue to shoot the PMC Bronze JHP ammo as range ammo, to continue the break-in process of the DB45R 1911.
I’m currently very near to crossing over the 1,000 round threshold with the Bul Armory SAS II Ultralight.
I visited the range a few days ago, bringing 200 rounds of ammo. I ran out of range time before I was able to shoot it all. I visited after work since I’ve to be at work every Wednesday now. I may make this my range day every Wednesday since my work isn’t far from XCal.
While I was waiting in line for a lane assignment, I happened to see some of the range’s rental selection. They’ve Staccatos, as well as several really nice 1911s. What I really want is to try the G43X and G48 (I may be purchasing one of those next year). I didn’t see those guns in their rental section but their rental section is very large and I’m sure they’ve a good selection of Glock rentals. I’ll check next time I go. I also wanted to try their P365, since I’ve seen more than one person asking, “Why buy a SAS II UL when a P365 is better?” In my opinion, that’s a rather lame comment since most folks aren’t cross-shopping those two guns (due to price as well as platform — both of those being quite different frome one another). Yeah, a P365 will conceal better, but P365s are also more difficult to shoot quickly and accurately. The SAS II UL has a bigger grip than the P365, but that doesn’t mean that an owner will have issues concealing a UL. The UL will almost certainly be less snappy and quicker to shoot. It’ll probably outshoot the G43X, too.
I shot 187 rounds of the 200 that I broght with me. Most of it was Fiocchi 115-gr FMJ, although some of it was Blazer 124-gr FMJ and Remington 124-gr FMJ. That puts me at 986 rounds through the SAS II UL, thus far.
I had 6 fails to feed (FTF) prior to the pistol course I attended a few weeks ago. I had one FTF during that class and one at the range visit this week. The total FTF count is now 8. 8 of 986 is 0.81 — that is the current failure rate in percentage.
The prior percenage was 0.96, with 6 fails at 623 rounds (back in May 9, 2023). I had several range visits where I didn’t have any failures. This could be due to me learning how to better grip this handgun, as well as me not shooting as much JHP (which tends to be high pressured, which may induce limp-wristing).
Why do I report this as a percentage? So many folks look at failure counts as hard numbers. They want it to be zero. In my opinion, to expect no failures is an impossible ask. Sooner or later, a gun will fail, especially since failures can be induced by the shooter, as well as out-of-spec ammo. Some ammo will be in-spec but will have large hollowpoint projectiles (which do not meet a specification). I don’t think it is logical to expect a handgun to meet every single variation of ammo specification, as well as account for owner-induced failures. So, I post the round count and count of failures and then convert both to a percentage. Percentages have better meaning, IMO. It tells a better story than a raw number of failures.
I still need to purchase the targets that were used in the pistol course I attended (as well as the target stickers).
I’ll post some range footage as soon as I’ve cropped a few sections for viewing. I mainly shot at 7 and 10 yards, some at somewhat fast paces. I also tried to practice accuracy. I shot several times at 15 yards, too. I’m still struggling with grip. I keep readjusting my weak hand after a shot — I need to find a better way to stop doing this. I’m subconsciously doing that.
I also forced myself to shoot the SAS II UL this go-around, since I’ve been neglecting the gun (and I’m also carrying it).
I brought some of my open boxed SD ammo to test the S15, as I initially thought it was having issues due to bad ammo. Another culprit could have been the mag (there was one magazine in particular that was having issues). Another culprit could have been me – I’d shot the gun toward the end of the visit and I was probably getting tired (hand/wrist/arm fatigue).
Right off the bat, I got two fails to feed, with the suspect mag (I’ve marked it). I ended up stopping everything, emptying the mag of ammo, and putting the ammo in a different magazine. The failures stopped.
I’m thinking I might ask Shield Arms to replace this mag. The mag is new and should be covered by manufacturer’s warranty. It’s odd that the failures don’t always occur, though. The ammo it was choking on was Sig Sauer V-Crown 147-gr JHP.
It also failed once when shooting Remington Golden Saber 147-gr JHP. It ate 21 other Golden Sabers without issue, though.
Those were the only failures, so it wasn’t really all that bad this time around.
I’m at 623 rounds through the S15 now. The gun is uncannily accurate. It doesn’t seen to be as snappy as the SAS II UL, but it has better grip surfaces (by far). Now that I know that it’ll eat JHP without issue, and now that I’ve tested the mags, I can actually consider carrying this gun now, although I’ll keep testing it (I’m still wanting to carry the SAS II UL, too).
I’m at 661 rounds through the SAS II now. I shot 38 rounds tonight, all Herters Target 115-gr FMJ. There were no hiccups or failures. I shot all the ammo at 10 yards, quickly (since I’ve the optic installed).
I’ll be working on posting range video footage this weekend, of both guns. I have footage from the last visit but the settings were out of whack and the field of view wasn’t the best (the framing was off-center, as well).
Next week, I’ll be attending my first handgun course. The plan is to use my current carry gun (SAS II UL). I’ll be bringing my Glock 19 as a backup gun, in case they state my SAS II is too small and in case the SAS II has a breakage. I’ve other guns I can consider as backup guns but most of my guns are DA/SA and I’m more used to SAO nowadays. I’ve several striker fired duty- and compact-sized guns but I’ve no holsters for them (nor extra mags). At this point in time, the Glock 19 is my best option (I’ve extra mags and several holsters for it).
I plan to shoot Blazer 124-gr FMJ for the course (was told that I’d need 200 rounds, so I’ll buy 4 boxes of 50). Blazer is reliable for me, but so is the Herters Target, so I may buy that brand instead, although the Blazer is just a few dollars more.
I was planning on a rifle course too, but I need the time to purchase mags and magazine pouches that’ll fit my carry belt. I may have to wait until next year for that, although I can also take a rifle course by XCal. We’ll see.
I went to the range tonight because I wanted to work off some steam (been busy with work and have been stressing).
I’d been thinking about my Grand Power and recently had someone reach out to me on YouTube. She said that she has the P11 and that she’d been having the exact same issue (fails to return to battery, or FRTB), but that her husband didn’t have the issues when shooting it. She hinted that it may’ve been limp wristing that caused it.
I did a bit of research and it seems that limp wristing can cause FRTBs.
I never realized that I could’ve been limp wristing the gun. It is rather slick, with no significant texturing on the grip.
I decided to begin taking it to the range to see if I can shoot it without experiencing the FRTBs. I shot 50 (well, 48) rounds of Koenig 110-gr JHP Match through it tonight and I didn’t have any failures. Note that the gun is configured a bit differently since I last shot it — I’m using a small Hogue rubber grooved slip-on grip, which helped with getting control of the handgun. I was ensuring I had a strong grip on the gun. I’ll continue to bring it to the range, shooting 50-100 rounds from it when I can, and trying to practice good grip technique so that I’m accurate as well as not limp-wristing.
I also shot 155 rounds from the Alpha Foxtrot S15 1911. The ammo of the night for that gun was Herters Target 115-gr FMJ with a splash of Fiocchi 115-gr FMJ. Whereas I didn’t have any issues last range visit, I had 8 FTEs this range visit. I shot the same ammo last visit, as well.
The issues could be (possible solutions are below, in italics):
Bad magazine – I shot with all six mags and only one mag generated failures, so I kept shooting with it to see if I was limp-wristing and causing the failures. I shot many rounds through that mag tonight and there was only one time where I got thorugh a mag without failures. I marked the mag and will put it aside. The plan is to use the other mags next range visit – if the failures stop, then I’ll know that the mag is the problem.
Bad box of ammo – I bought 200 rounds of Herters (2 x 100-round boxes). I got through one box with only two fails to extract. The other box had five FTEs. The Fiocchi had one failure – not only did it the spent case not extract, but it was still fully in the chamber, and the slide did not lock back (it was the last round of the mag). Also, I noticed that the slide would sometimes seem to be moving a bit slower than normal after a round is fired, which is usually indicative of inconsistent amounts of powder within the case. As well, some of the ammo looked funky where the case crimps onto the projectile, as if the ammo had possible QC issues. I’ll bring some good JHP with me next range visit, to see if the issues still occur with good ammo.
Limp-wristing – I won’t count this out, since the FTEs started occurring mid session of my range visit. I tend to fatigue myself as I practice (this is normal). Next range visit, I’ll test the S15 (and the other 5 mags that didn’t have issues) before shooting any other guns.
I did have fun shooting the Grand Power again. I was accurate with it. I shot it once at 10 yards but the spread was wider than when I shoot the S15 at that range, which I initially thought was odd until I realized that the S15 has far better grip texturing. I ended up sticking with shooting at 7 yards.
The S15 is accurate AF! I spent a large amount of time shooting at 10 yards and was accurate. Not only that, there were times where I was shooting pretty fast and my groups were tight as I shot further out. And that was with irons. This gun is uncanny, but it’s really because of the front checkering on the grip. It’s going to seriously spoil me. I’m already thinking about selling all my other 1911s so that I can focus on 1911s and 2011s that have front checkering. Yes, I can get checkering added to my existing 1911s, but some gunsmiths won’t touch non-US guns and all guns that get checkering will need to be repainted/refinished.
I also now have just under 500 rounds through the S15. I’m slowly accumulating the round count on this gun. I’ve just under 1600 rounds through the GP P11.
This is the first time I’ve tried a range other than Elite. Elite closed last weekend, so today I visited XCal in Ashburn (30 min drive – 30 miles).
Shot 48 rounds of Norma 115-grain FMJ. There were no fails.
I also shot 64 rounds of Fiocchi 115-gr FMJ. There were no fails.
Total rounds this session was 112 rounds of FMJ. There were no fails.
I spent a majority of the 1-hour session adjusting my new optic (Holosun HS507K-X2 ACSS). It was initially frustrating because I couldn’t hit point of aim at all. I kept adjusting the sight and was able to get proper windage but couldn’t get the proper elevation…no matter how much I tried, I couldn’t get the dot lower than 6-8″ above the bulls-eys when shooting at 10 yards.
I finally stopped and decided to remove the optic wedge I’d installed (was supposed to fix an issue with the SAS II UL having elevation issues when an optic is mounted). Once I removed the wedge, I reinstalled the optic and was immediately hitting the bulls-eye. It still needs to be fine-tuned, but I’m quite happy with the functionality of the optic and that I solved the elevation issue!
I bought a crapload of ammo, but only got to shoot 112 rounds, since I was attempting to adjust the optic’s point of aim and since I had the issue with elevation.
I wish I’d shot a bit more to break the 500 round count.
I’ll attempt to visit again next week. I’m probably going to apply for membership before then.
I almost decided to put the irons back on tonight, at the range. The only thing that stopped me was that I’d forgotten to bring the irons with me. That forced me to bird-dog the issue – I didn’t need that optic wedge I’d installed and I shouldn’t have immediately installed it. That’s what I get for believing an internet source – bottom line is, don’t believe everything you read on the internet! Trust but verify. If I’d have installed just the optic and not the optic wedge, I’d have not had an issue at all.