I wanted a place to discuss my handguns and firearms in general. Everyone seemingly has lots to say about guns, so I promise you this won't be a rant blog.
Regarding the SDS Imports 1911D B45R I recently purchased, I mentioned here that it had problems with some non-OEM mags. Specifically, Wilson Combat mags were hanging upon insertion attempts. The Metalform GI mags were exhibiting the same symptoms, too.
I stated that I’d ordered a Wilson Combat magazine release. Well, it arrived Friday. I’d never removed and installed one, so that was something new to me, and it took awhile to understand how I needed to remove it, as well as how I needed to install the new one. It was simple, once I understood what I needed to do.
Once it was installed, I checked to see if the mags would snag/hang on the mag release catch. For the WC mags, they don’t. The GIs are weird, as they begin to stag and end up not snagging – there’s some slight resistance. The feed lips on the GI mags are not rounded, so I believe they’re more susceptible to resistance. I think they’ll wear-in over time, though.
So, I recommend the WC magazine release button, spring, and screw (they’re not a set…you’ve to buy each). As of now, the cost for the three parts is approx. $25.
I went to the range today to have my new 1911 transferred to me – the SDS Imports 1911 Duty B45R.
I got there at 9 AM. I turned in the paperwork by 9:15 AM. I was given the gun at 9:20 AM.
The gun was immaculate. It also appears that someone cleaned the gun. It wasn’t pristine-clean, but it had no cosmoline on it (I’m not sure how these guns are normally shipped/stored – many are covered in preservative, which is what cosmoline is). It did have lube on the the frame and slide rails. I cleaned it anyways.
Surprisingly, the gun came with two Mecgar mags! I was expecting one mag, so that’s a big plus. I’ve spoken with other folks and they state that theirs came with one mag. My gun also came in a case. Those other folks stated theirs came in a cardboard box.
The gun is cerakoted but almost looks like it’s parkerized. It is black with a silver trigger and barrel. It has backstrap serrations but has a bare frontstrap. The ambi safeties are not bulky and have extended levers…they look nice!
I’d two other mags – branded Wilson Combat. I planned to use them with this gun at the range this evening. I also planned to use my ACT mag that came with my Metro Arms ACC 1911.
I had a small stash of 45ACP – two boxes of International 155-gr frangible ammo, which doesn’t perform all that well. I also bought two 50-round boxes of PMC Bronze 230-gr FMJ from the range when I arrived. Before I’d left for the range, I’d had the time to swap out the black plastic OEM grips with brown/tan/black grippy G10s that complement the gun.
I ended up shooting the two boxes of International and shot one of the two boxes of PMC. The PMC felt as if it were hot ammo (it always does). The International ammo surprisingly had no misfeeds.
One of the mags caused a failure at the very first round within it’s mag – It was the ACT mag. I ejected the mag, stripped it of ammo and put it to the side. I would not use it the rest of the range session.
The Wilson Combat mags were not flawless, but I’ve found it wasn’t a fault of the mags. The gun has a mag release that will work for the Mecgar (and ACT) mags but will not work well with the WC mags because it needs to be beveled. The mags would sometimes not want to be inserted. To fix this, I need to order a mag release from Wilson Combat. It will swap into the SDS 1911 without issue and will work with non-WC mags.
Pics of the gun:
A photo of the SDS 1911DB45R after the transfer.These grips are NICE but a bit too slick for range use.I shot the gun for the first time tonight (17 Feb). I used these G10 grips. I’ve no complaints…they work well, and I had no issues controlling/gripping the gun.
Pics of the range targets:
SDS 1911B45R first shots. This is 32 rounds of PMC Bronze 230-gr FMJ at 7 yards. I was getting familiar with the trigger, sight picture, and the ammo.I wanted to directly compare the PMC Bronze 230-gr FMJ and the International frangible 155-gr ammo. I bought maybe 250 rounds of the International maybe 2 years ago and it’s inconsistent ammo but it’s better than not having ammo. Upper left and lower right is PMC. Upper right and lower left is International. All targets have 8 rounds. All were shot at 7 yards.These were shot at 10 yards, using International frangible 155-gr ammo. First, I shot center, then I shot upper left, then upper right, and lastly I shot lower left. I’m getting tired and it’s showing…the rounds aren’t hitting where I’m aiming. The groups are still decent, though, especially the first group.These were at 10 yards, and all are shot with International 155-gr frangible ammo. 8 rounds were shot at each target. I’m getting tired. The groups aren’t bad, though.This is 4 mags of 8 rounds each. The distance is 7 yards and I used International 155-gr frangible ammo. These were fast (not exactly rapid) fired, maybe 2 shots a second, starting from low ready for each mag. Not bad for me.
Before I left the range, I looked at their store items. They carry WC mags and had one full size 1911 mag left. I bought it (since it’s price was $34, which is rather inexpensive from what I remember of WC mag prices).
The gun is solid. There’s absolutely nothing wrong with it, aside from the mag release. It’s accurate. It’s smooth. The trigger is awesome. The finish and fitment is on par with $700-800 guns (Springfield Armory Garrison), in my opinion, yet I bought this gun for under $500. My only misgiving was that I didn’t get it in stainless steel (that version is $100 more).
