Category: range visit

Categories
1911 Duty range report range visit Tisas

Revisiting The Tisas Duty 1911

I’ve been keeping a running tally of notes after visiting the range – keep in mind that I’ve not been to the range with this particular gun in quite a while (2022). Here’s the latest version of my notes:

UPDATE 1:

  1. Range photos with detailed captions are at https://photos.app.goo.gl/yrLbWQNMmDjgJCzV8. Note: I’m not sure if Reddit will choke on Google’s URL shortener – I’ve had problems with it in the past.
  2. I brought 2 Wilson Combat mags with me, the two that the gun came with, and 1 ACT mag from another 1911. The ACT mag choked the gun once, and I knew it would be problematic because it’s been acting up the last few range visits (ie, it wasn’t an ammo issue). I bought another WC mag from the range store – it will replace the ACT mag. I will keep the ACT mag in case I need to scavenge parts from it.
  3. The B45R loved PMC Bronze 230-gr FMJ and I shot 50 rounds of it (this ammo always feels peppy). The other ammo I used was International 155-gr frangible ammo. That ammo is crappy but it never choked the B45R. My Metro Arms hates it. I also noticed slide slowdown (an indication of low powder charge) but only when shooting it out of the Metro Arms…I didn’t notice any of that with the B45R. I shot 100 rounds of the International ammo.
  4. I bought some G10 grips to replace the cheap-feeling grips that came with the gun. They work very well, and I expected nothing less (all of my other 1911s are using G10s).
  5. Issues:
    1. The WC mags will sometimes hang up in the mag well. It seems that the magazine catch/release is blocking insertion. If I hammer up on the mag, it blasts past but smacks into the upper portion of the gun (that’s probably not a good thing). If I actuate the release button a tad, the mag is allowed past. I’m hoping this issue will go away. This only happens with the WC mags. I’ve three 7-round Mecgar mags on the way here and they should arrive tomorrow. I’ll see if those get hung up. UPDATE: Found someone else reporting the same issue here – replaced the OEM mag release with a WC mag release; tested both the WC mags and GI mags – both can now be inserted without issue.
    2. This is more of a non-issue for me but has been an issue for some folks. The grip panel bushings have been said to be “off” and will not accept non-OEM screws. I had no problem using the screws provided to me by Coolhandgear.com to install their grips. I tried two sets of differing screws and had no issues.
  6. I’m absolutely loving this gun. My target gun was a Springfield Armory but I had a very difficult time deciding exactly what I wanted and then had a difficult time finding them in stock. So, I did research and decided to try the SDS 1911s. This gun hits way above it’s weight…it is very much comparable to a Springfield Armory Garrison (but railed). The B45R was well under $500, but has a forged frame (what other non-GI 1911s are in this price range that offer both forged frames and slides?). I basically stole a great 1911. I also don’t have any issues buying foreign/Turkish guns. I’m a 10 year military combat veteran, so I’m as patriotic as any self-proclaimed patriot, and have probably sacrificed more. ALL of my 1911s are non-US and I’ve Caniks and Tristars as well, one being my CC gun. I’ve no problem with any non-US-made guns.
  7. The plan is to maybe change/fit a silver barrel bushing but maybe in 6 months or so.

UPDATE 2:

  1. I visited the range tonight and put more rounds through the 1911 – 169 rounds to be exact. 150 of that was PMC Bronze FMJ and 19 was Remington HTP 185-gr JHP. There’s now a total of 319 rounds through the gun.
  2. One JHP failed to feed but the gun is very dirty now (haven’t cleaned it since the day I received it). As well, it choked when using one of the three GI mags I bought – the round was the first in the mag. No, 19 JHP rounds isn’t much but good JHP 45ACP ammo isn’t exactly cheap, so that’s going to have to suffice for now.
  3. I decided to test it at 12 yards out. I usually don’t shoot at distances longer than 12 yards. The gun is accurate, even in my hands (although there were flyers).
  4. The gun is tearing up my hand at the beavertail – still trying to determine how. I’m being pinched badly at the webbing of my hand where the two skin textures meet. I’ll use gloves the next range visit. UPDATE: I believe it is the back of the right-side (ambi) safety that is rubbing my hand raw. It isn’t sharp but isn’t rounded either…over long periods of time, it’s an issue. I may look into getting a one-sided safety.
  5. I’ve a Wilson Combat magazine release on the way. That should fix mag insertion problem with the WC and GI mags. No longer an issue.

UPDATE 3:

  1. I’ve shot 429 rounds from my SDS Imports DB45R 1911, thus far. Since I’ve been curious about it’s carry capabilities, I’ve been trying to shoot JHP from it, initially with mixed results.
  2. I initially shot Remington HTP 185-gr JHP, which generated several failures to feed (FTFs).
  3. Federal LE 185-gr JHP was used, as well (maybe 25 rounds), which also generated some FTFs.
  4. International Cartridge Corporation’s (ICC) 45ACP 155-gr frangible hollow points were used. For the most part, these shot without issue. That ammo can be used as defense ammo.
  5. I also fired 20 rounds of Underwood ($$$) 45ACP +P 230-gr JHP. 8 of the 20 rounds generated FTFs. I used Wilson Combat mags with this ammo. Since this ammo is expensive and since it generated so many FTFs, I will stop shooting that ammo through the DB45R. Once I suspect that the gun will shoot it without FTFs, I’ll test the ammo again.
  6. Inceptor ARX 118-gr defense ammo (non-JHP) was used, using the WC mag. There were no FTFs.
  7. I shot PMC Bronze 185-gr JHP (non-SD ammo), using the WC mag.. There were no FTFs.
  8. Hornady Critical Defense 185-gr JHP was shot through the gun, using the WC mag.. There were no FTFs.
  9. So, I now know that I can use the following ammo as viable ammo for self defense:
    ICC 155-gr FJHP
    Inceptor ARX 118-gr
    PMC Bronze 185-gr JHP
    Hornady Critical Defense 185-gr JHP
  10. In my view, the ammo problems are more than likely due to projectile ogive dimensions as well as hollow point size. If it were an issue with the gun, ALL the JHP I tested would be generating FTFs. There are no specification standards on ogive or projectile dimensions in today’s ammo market, so it’s difficult to make a gun 100% reliably eat all mass-produced ammo, and 1911s aren’t Glocks, so….

I plan to continue to shoot the PMC Bronze JHP ammo as range ammo, to continue the break-in process of the DB45R 1911.

Categories
1911 2011 Bul Armory handguns range visit SAS II Ultralight

SAS II UL Optics Adjustment Issues – The Wedge Was Not Needed!

My range notes for today’s range visit:

This is the first time I’ve tried a range other than Elite. Elite closed last weekend, so today I visited XCal in Ashburn (30 min drive – 30 miles).

Shot 48 rounds of Norma 115-grain FMJ. There were no fails.

I also shot 64 rounds of Fiocchi 115-gr FMJ. There were no fails.

Total rounds this session was 112 rounds of FMJ. There were no fails.

I spent a majority of the 1-hour session adjusting my new optic (Holosun HS507K-X2 ACSS). It was initially frustrating because I couldn’t hit point of aim at all. I kept adjusting the sight and was able to get proper windage but couldn’t get the proper elevation…no matter how much I tried, I couldn’t get the dot lower than 6-8″ above the bulls-eys when shooting at 10 yards.

I finally stopped and decided to remove the optic wedge I’d installed (was supposed to fix an issue with the SAS II UL having elevation issues when an optic is mounted). Once I removed the wedge, I reinstalled the optic and was immediately hitting the bulls-eye. It still needs to be fine-tuned, but I’m quite happy with the functionality of the optic and that I solved the elevation issue!

I bought a crapload of ammo, but only got to shoot 112 rounds, since I was attempting to adjust the optic’s point of aim and since I had the issue with elevation.

I wish I’d shot a bit more to break the 500 round count.

I’ll attempt to visit again next week. I’m probably going to apply for membership before then.

I almost decided to put the irons back on tonight, at the range. The only thing that stopped me was that I’d forgotten to bring the irons with me. That forced me to bird-dog the issue – I didn’t need that optic wedge I’d installed and I shouldn’t have immediately installed it. That’s what I get for believing an internet source – bottom line is, don’t believe everything you read on the internet! Trust but verify. If I’d have installed just the optic and not the optic wedge, I’d have not had an issue at all.

Before removing the optic wedge

After removing the optic wedge
Categories
ammo Bul Armory defensive ammo range report range visit SAS II Ultralight

Summary of the SAS II UL’s 2nd Range Visit

I went to the range yesterday and shot approximately 160 rounds of ammo. Half of it was FMJ and the other half was straight-up SD ammo (none of the cheap stuff).

Some quick observations:

  • I cleaned the firearm for the first time today (a day after the 2nd range visit). It was filthy. I could see preservative oil in the upper reaches of the slide (looked like rust but I know it wasn’t – tell-tale sign of preservative oil). I didn’t deep-clean the gun – I only field-stripped the gun, but I did remove the firing pin and clean it (I didn’t have any pipe cleaners, so I didn’t clean inside the channel). I also cleaned the extractor claw (did not remove the extractor, though). The claw was nasty. The barrel was nasty and had some crud in the chamber that took some time cleaning.
  • I took the opportunity to also take apart the two mags that came with the gun. I cleaned and oiled them (light coat of oil).
  • I noticed that the rear sight was loose. I’ll need to remove the rear sight, clean the threads, and then use blue thread locker to secure it, but for now, I just tightened the rear sight screws – I’ve an optic on the way here, and I’ll be removing the rear sight anyways.
  • I received two more OEM mags today, as well as a flat trigger shoe. I thought I could quickly install the new trigger shoe – nope…I need a 1.3mm allen wrench to remove the trigger shoe. That’s going to be a bitch to get off, too – it will take time, IF it’s not secured with threadlocker. If it is, it’ll take even more time.
  • I also received two optic shims (I only needed one but I wanted redundancy). The HS507K will require the shim, otherwise I won’t be able to adjust it properly (this is a known issue with the 507K and the SAS II UL).
  • The gun fired OK during the range visit. I shot the following ammo: Herter’s Defense in 115-gr JHP, Sig V-Crown Elite Defense 124-gr JHP, Koenig Competition 110-gr JHP, Remington Golden Saber 124-gr BJHP and 147-gr BJHP, and Hevi Duty 100-gr frangible flat-nosed ammo. I also brought some Fiocchi 115-gr FMJ ammo.
  • I had two fails to feed (FTF) with the Sig ammo, one of the FTFs being a double-feed. This ammo shot a tad bit high.
  • I had two FTFs with the Koenig ammo – same deal, one of the FTFs being a double-feed. As well, this ammo shot 2-3″ high! To hit the bullseye, I had to aim 2+ inches low.
  • I had no failures with the rest of the ammo, although the Hevi Duty frangible ammo shot high.

Basically, it seems that any light-for-caliber ammo that is shot from this gun will land high. That was my experience with Inceptor ARX (65-gr fluted tip) too.

So, we’ve shot a total of 336 rounds of ammo from the SAS II UL, thus far.

I still need to master the trigger of this gun. It’s a bit more difficult to shoot (and be precise) than my other 1911 9mm handguns, part of the issue being recoil management. I’ll get better as I spend time with the gun.

Categories
ammo Bul Armory defensive ammo fail to feed range report range visit SAS II Ultralight

Bul Armory SAS II – First Range Visit

I want to focus on two things in this after action report: 1) ammo and reliability; 2) shooting – accuracy and recoil management

About shooting reliability —

So, I took the SAS II to the range today. I took maybe 200 rounds of various types of ammo. Much of it was JHP. Some was actual defensive ammo. Some was light for caliber. Some was heavy for caliber. Some was FMJ.

I shot Inceptor ARX (65 gr), Winchester Silvertip (115 and 147 JHP), Federal Hi-shok (115 gr JHP), and Fiocchi (115 gr FMJ).

2 of the ARX failed to feed, but I expected as much with this ammo…not the fault of the gun.

There were two failures to feed with the Federal Hi-shok (of 100). Hi-shok is considered to be personal defense ammo, but it’s bottom-feeder ammo – I wouldn’t carry it but it’s good enough for the range. And again, the SAS II ate 98 of 100 of it.

I shot a total of 175 rounds. The actual defensive JHPs fed without issue. Of note, the 147-gr ammo also fed without issue, which was great (Bul Armory recommends using no higher than 124-gr).

Excluding the ARX failures, the failure percentage of this range visit is 1.14%.

I know 175 isn’t much, but JHP ammo isn’t cheap, especially legit defensive ammo.

IMO, the gun is reilable enough. I know some folks have been complaining of FTFs, extraction issues, and even some fails to return to battery. I’m not seeing any of that, but my gunnery has improved quite a bit in the last few years. There were many times where I thought a few of my guns had issues and they all turned out to be issues with me. Folks who’ve been shooting for far longer than I have can sometimes experience limp wristing, for example. The SAS II is light – it needs a firm grip, IMO.

Speaking of limp wristing, we’ll now speak on accuracy and recoil management —

I don’t consider this gun to be generally snappy, although I was shooting some loads from it today that made it snappy as hell (defense ammo). Even so, I was able to manage recoil quite a bit, which is saying a lot, because I’m not the strongest guy in the world. I did come home with fatigued forearms and wrists, but that means I’m going things correctly (from my undstanding, if you’re going home with tired arms/hands/wrists, you’re executing properly).

I keep hearing folks say that the SAS II is snappy. Recoil impulse is a subjective thing, but for such a light gun, I’d have thought the recoil would’ve been much worse than it is. I remember first shooting my Glock 22 – that was an eye-opener, as I’ve shot 40 S&W without issue in the past, but not from a Glock. The G22 is light and the 40 S&W is not known for light recoil. I’d previously shot 40 S&W from metal-framed guns without issue. The G22 took me for a ride and I was very disappointed, because the recoil was harsh. The SAS II is on par with my Springfield Armory XD9 subcompact (which I shoot very well), as far as recoil is concerned, in my opinion, at least.

Accuracy-wise, it’s extremely easy to hit where you want, at realistic distances. This is not a long distance gun, but some folks can easily hit steel at 25 and even 50 yards. The trigger is crisp, as is the sight picture of the sights, which helps.

I also was able to fit the SAS II into my Tenicor Certum holster without issue (had to loosen the retention since the SAS II is thicker than my current carry gun). I then put it inside my waistband and was quite surprised – it carries far better than my single stacked Commander! The grip is much shorter and tucks in better.

Overall, I had a great time tonight. I need to continue to test ammo with this gun. Once I find a good reliable batch of ammo and I’ve shot the gun a while, I’ll start carrying it.

Range target photos are below:

First two mags; first mag was center-mass and second mag was the lower left group.
First five mags, 7 yards, various types of ammo.
Four mags (one per target). I didn’t write down at what distance I was shooting, but I keep thinking its 9 yards.
15 yards out; me being tired and not be able to see where to aim; 2 mags
Range Footage – not pretty but not meant to be; I film my shooting for training purposes and focus on my hands and the gun so that I know when I’m limp-wristing, when I’m slapping the trigger, when I’m letting the gun control me, or other things. Sometimes it’s worth showing though.
Categories
AK-V PSA range visit

PSA AK-V MOE – First Range Visit!

I had fun today!  I ended up shooting 199 rounds from the AK-V.  In an hour.  I had 100 rounds of Wolf 115-gr FMJ and Winchester White Box 115-gr FMJ.

I started out at 10 yards, then went to 25, then to 20, then focused on 15 yards.  I had no issue staying on the paper while out to 25 and when I moved to 20 (to better see where I was shooting), I ate the bulls-eye up!  This pistol is easy to shoot.  It has very little recoil and you can shoot it fast with ease.

I did have 4 FTEs, though, with one mag.  It was the CZ Scorpion mag that I believe is the issue.  It’s spring is very stiff, to the point that my finger is sore from loading it.  I think it may break in.  We’ll see.  It wasn’t related to ammo because it did it with both brands of ammo.  As well, the bolt didn’t hold open several times.  There was also a time where one round didn’t want to feed and was jammed into the chamber.  When I tried to get the bolt to hold open so I could get the round out, it slammed shut, forcing the round into the chamber.  When I tried to eject the round, I couldn’t get the bolt open, but the trigger was live so I fired it out.  The casing came out but I didn’t see where it went (so I could look at it).  It did this a second time as well, but I was able to get the round out.

I have range footage but my camera wasn’t positioned well (I couldn’t preview the footage to ensure proper framing).

Hopefully, I can get better range footage next time.

Categories
Beretta Bersa Grand Power P11 PX4 Storm range visit Thunder Plus

Range Visit

I went to the range today and brought the Grand Power P11, the RIA 22TCM, and of course I bought my current carry gun, the Bersa Thunder Plus (I’m carrying the PX4 less now, since it is so thick…it’s lumpier and I don’t like that it feels so large on my hip).  I couldn’t use my RIA, though, because I forgot to bring it’s magazine.

I brought 200 rounds of Wolf 115-grain FMJ for the P11.  I fired 150 rounds of it.  I bought 50 rounds of Speer Lawman 95-grain FMJ at the range for the Bersa.  I fired all of that.

I started out with the P11.  I ensured it was lubed properly (using synthetic motor oil – 5w20 Motul) beforehand.  It failed to return to battery once in that first magazine.  It did it again on the 6th magazine (12-round mags).  Then I did twice more through the last two mags.  It probably was pretty dirty with firing Wolf ammo after 138 rounds, so that’s probably why it was failing.  Wolf is REALLY dirty and covered in some type of semi-sticky coating…not exactly conducive to the inner workings of a gun with tight tolerances.

12 yards out with the P11 – not used to shooting that far out…I shot 12 rounds but 3 rounds missed the paper, and the group was not tight.
12 yards out, next 12 round mag with the P11.  The first shots were landing at the top of the target.  I had to 6 o’clock hold the sights to get the rounds to hit around the red.
Went back to 7 yards out.  Notice how the rounds are very vertically oriented.  Need to ensure the front site is lined with the rear dots, but for self defense purposes, this is superb, IMO.
7 yards with the P11…two mags worth.  Still hitting a bit up high but they’re again pretty vertical.
7 yards with the P11 – two mags…this is tight as hell, but I’d still like to work on the 1-2″ left drift of the grouping.  That’s trigger slap or me not using my support hand enough (for stabilization).  Was also shooting a bit fast.
54 rounds @ 7 yards with the P11.  Worked a bit on DA trigger pull (also did quite a bit of dry fire to try to get a feel for the DA on this gun…it’s different than the DA on the PX4, with the PX4 having the better DA trigger, IMO).  So, two mags to the head and two mags to the torso with this target, with several doube-taps using the last 10 or so rounds.
50 rounds of Speer Lawman FMJ 95-grain ammo.  I hated this ammo…it caused the Bersa’s beavertail to sting the webbing of my hand.  After one round of sting, I immediately grabbed my gloves, but shooting with gloves is difficult for me.  The rounds have a vertical pattern, though.

That Speer Lawman ammo for the .380…it was stinging my hand.  I’ll have to avoid that ammo in the future.  It seems I’m going to need to develop a listing of “to avoid” ammo for this particular handgun.

So, I’m now at a round count of 1269 for the P11 and 373 for the Bersa.  I’m not sure if I’ll ever get rid of the fails to return to battery with the P11.  I wanted to give the gun a fair shake by trying a thicker lube, but maybe using Wolf negated the usage of thicker oil (oil that’ll stay put instead of migrating).  There’s always something with the P11…too many excuses being used to explain these issues.  :/  The Bersa is still cool to shoot.  The trigger is smoothing out.  I’m still not as accurate with it as with the P11 or PX4, though…and it’s trigger isn’t all that spectacular when compared to those aforementioned handguns, too.  But it’s definitely utilitarian.  The only thing about this gun that I really hate is it’s recoil sting with certain ammo.

I’ll continue to shoot both guns, although I probably need to put more rounds through the PX4.

Categories
1911 extractor fail to feed feed ramp range visit recoil spring SP2022

Bersa Thunder 380 Plus Listings; Metro Arm 1911 Woes

I’ve had several people reach out to me asking about where to find good-priced Bersa Thunder 380 Plus models.  Here are some:

All of those are listed on Gun Broker.  There were at least 7-10 of them listed, but most were over-priced.  I only listed those that were under MSRP, but I did list the Combat Plus because many people are asking where to find those models and supply is scarce.

Also, a few weeks ago, I ended up taking my Metro Arms 1911 (the American Classic Commander, specifically) and my Sig SP2022 9mm to the local range.

I also ended up putting 50 rounds of American Eagle 124-grain through my current carry gun, the Grand Power P11, just to test to see if it was still having issues returning to battery (it ate all 50 rounds without issue).  I’m currently at 582 total rounds through that gun.

7 yards out, American Eagle 124-grain, Grand Power P11

The SP2022 ate 60 rounds without issue.  That handgun is fantastic and is extremely easy to shoot accurately.  I’m at 279 rounds through the barrel with NO issue whatsoever.

7 yards, Remington UMC 147-grain flat-nosed FMJ, Sig SP2022 9mm

The Metro Arms has been problematic.  I shot 48 rounds through this gun this session and had many failures to feed.  In fact, when I go through my range log, This gun has a history of failing.  It isn’t the mags that are causing the issue (it happens with all three mags and two of them are new and from Wilson Combat).  I actually searched and found that this is more than likely an extractor issue.  I checked and found it was too loose.  I tightened it up and now need to revisit the range to test to see if that helps.  If it doesn’t, I’m going to buy a new recoil spring and extractor.  That should fix the issue.  Another thing of note is that the feed ramp has some major abrasions from the last range visit when I shot Tula through it…it did NOT like Tula and I’d made a note of it (and the feed ramp) in my range log.  I shouldn’t need to polish the ramp with so little ammo through the gun, especially since the ramp had a mirror finish when I received the gun.  The gun only has 188 rounds through the gun.

7 yards, Winchester White Box 230-gr FMJ, Metro Arms ACC45, one FTE (24 rounds total)

As well, the point of impact is not hitting where I’m aiming (I’m aiming for the red with the front sight covering the X.  One thing I neglected to check was my trigger finger placement and how I was actuating the trigger.

I may visit the range tonight just to test the 1911.

I still haven’t shot my AR-15 yet, either.  I’m saving that for Father’s Day.  🙂