Category: Tisas

Categories
1911 2011 9mm double-stack double-stacked Tisas

Let’s Discuss Several Several Things About the Tisas Carry

I’ve been to the range twice with the Tisas Carry DS9.

I’ll share some information about the first range visit. I also suspected some of the things we discussed in my last post would be apparent during the first range visit.

The trigger had issues. The gun initially had a thick walled trigger. While the trigger itself wasn’t heavy, it wasn’t light either, so that’s a wash. The trigger wall was stiff, but I shot maybe 130 rounds from the gun, so the wall softened a bit. As well, the trigger is now lighter by 1 lb.

Between the trigger’s issues and the sights, I was having issues hitting where I aimed. I shot low (90 degrees low) with every shot — not low left, but directly low. I’m not sure how to use the U-notch sights, but I’m thinking they’re off by a bit, at least.

The gun didn’t hiccup at all during the first range visit. I shot a mix of ammo, some being HP, some being SD HP, and some being FMJ. The gun is flat-shooting, too.

When I got home from the first range visit, I sat while watching TV and kept racking the gun and pulling the trigger to get that thick wall to wear-in as quickly as possible.

When I went to the range next (two days later), I shot 187 rounds. Quite a bit of ammo was shot, some HP, some SD ammo, and a lot of range ammo. I had one fail to feed one one HP (I think it was Winchester range JHP). I put it back in the magazine and it feed and shot successfully.

The gun also shot a lot better, probably due to the trigger breaking in. Also, I man-handled the gun, as the first range visit, I was sloppy with gun control (recoil management and probably trigger control). My grouping were MUCH better this range visit.

I now have 317 rounds through the gun. The gun has yet to be cleaned, which says a lot, because I’ve looked in the gun and it’s pretty filthy. The rails were overly lubricated, which may have helped. I may clean it tomorrow, as I’m not intentionally trying to induce filth-related failures.

I also published a video. I’ll be producing a longer duration video soon. The short duration one below lacks some information (I had to make it fit into a 15 minute timeframe).

Categories
1911 2011 double-stack Tisas

I Purchased A Tisas Double Stack 1911!

This is my annual purchase for 2024!

I mentioned not long ago that Tisas is now making double stacked 1911s. I also have documented my journey with the Tisas Duty BR45 that I bought 2 years ago.

It is almost 1 o’clock AM and I was viewing availability of the new Tisas double stack 1911s. I was watching to see if I could find low priced variants, and also was waiting to see reviews of them – there are not all that many, currently. I did not intend to purchase until I noticed that the prices were creeping upward. As well, most places that had them earily in the week had sold out. I decided to buy now.

I bought a black Carry model. I’d been studying the Duty variant but none of those have been available…I can get one of those later, if need be. I was also looking at the MAC DS varaint, but didn’t feel like spending $900 on a 1911 (even though that price is below MSRP).

Note that the Tisas will be MIM-less (all but the recoil spring plug). Also, the gun comes with 2 mags. As well, the gun is optics-ready and the cover plate does not have the rear sight attached (which is great).

I’m excited about this gun, as it will be my second legit 2011. I saw some Prodigys that were marked way down from MSRP, but those were still $1100. I also looked at Apollo 11. This gun also undercuts the LFA Apollo 11 by a fair margin ($300) and comes with an extra mag, as well as having no MIM.

I’m happy with my single stacked Tisas and know they’re reliable, so I decided to give their 2011 a try.

This time, I bought from TheGunDock.com, mainly due to their lower pricing.

As with every gun purchase, I’ll document my journey with this gun.

UPDATE (2/10/2024): I waited two days for the gun to ship, but my FFL hasn’t yet sent it’s FFL information to the place I purchased the gun. They sent it to me by mistake. The gun store requires the FFL to send the info, not the person buying the gun. Until my FFL can follow the process, shipping won’t occur. I asked them to resend the info again, but it was late in the afternoon and I don’t think they saw my email. I may get the gun by the end of next week, IF my FFL clears up their mistake either tomorrow or Monday.

Categories
2011 9mm Tisas

Tisas is Now Producing 2011s!

So, I was checking Reddit today and saw a post that Tisas had listed a double-stacked 1911 on their website product list. Within an hour, there were like 5-6 other posts (in the r/1911 subreddit).

I decided to check the product page and was shocked. I thought they’d produced a Para-patterned 1911, but they actually produced THREE (3) 2011-patterned 1911s. They producted a 5″ variant, a 4.25″ variant, and a 5″ variant of their Night Stalker SF.

Not only that, but typical recent budget 2011s offer optics cuts that remove the rear sights. The Tisas variants will allow the rear sights to stay in place when using an optic. They’re also using 1/3rd co-witness of the rear sight through the mounted optic.

What’s the difference between Para- and 2011-patterned handguns? Para-patterned guns have the grips a permanent part of the frame. The frame and grip are one piece. 2011-patterened handguns have modular polymer grips that are separate from the frame. Many folks confuse Para-patterned double-stacked 1911s as 2011s, when there’s a distinctive difference.

Anyways, here are two videos: one of the 5″ Duty DS and the other of the 4.25″ Carry DS.

UPDATE (2/8/2024): I’ve removed the YouTube videos from this post, as the publisher marked them as private. It’s a bit annoying, because the publisher was Tisas.

Categories
1911 Duty range report range visit Tisas

Revisiting The Tisas Duty 1911

I’ve been keeping a running tally of notes after visiting the range – keep in mind that I’ve not been to the range with this particular gun in quite a while (2022). Here’s the latest version of my notes:

UPDATE 1:

  1. Range photos with detailed captions are at https://photos.app.goo.gl/yrLbWQNMmDjgJCzV8. Note: I’m not sure if Reddit will choke on Google’s URL shortener – I’ve had problems with it in the past.
  2. I brought 2 Wilson Combat mags with me, the two that the gun came with, and 1 ACT mag from another 1911. The ACT mag choked the gun once, and I knew it would be problematic because it’s been acting up the last few range visits (ie, it wasn’t an ammo issue). I bought another WC mag from the range store – it will replace the ACT mag. I will keep the ACT mag in case I need to scavenge parts from it.
  3. The B45R loved PMC Bronze 230-gr FMJ and I shot 50 rounds of it (this ammo always feels peppy). The other ammo I used was International 155-gr frangible ammo. That ammo is crappy but it never choked the B45R. My Metro Arms hates it. I also noticed slide slowdown (an indication of low powder charge) but only when shooting it out of the Metro Arms…I didn’t notice any of that with the B45R. I shot 100 rounds of the International ammo.
  4. I bought some G10 grips to replace the cheap-feeling grips that came with the gun. They work very well, and I expected nothing less (all of my other 1911s are using G10s).
  5. Issues:
    1. The WC mags will sometimes hang up in the mag well. It seems that the magazine catch/release is blocking insertion. If I hammer up on the mag, it blasts past but smacks into the upper portion of the gun (that’s probably not a good thing). If I actuate the release button a tad, the mag is allowed past. I’m hoping this issue will go away. This only happens with the WC mags. I’ve three 7-round Mecgar mags on the way here and they should arrive tomorrow. I’ll see if those get hung up. UPDATE: Found someone else reporting the same issue here – replaced the OEM mag release with a WC mag release; tested both the WC mags and GI mags – both can now be inserted without issue.
    2. This is more of a non-issue for me but has been an issue for some folks. The grip panel bushings have been said to be “off” and will not accept non-OEM screws. I had no problem using the screws provided to me by Coolhandgear.com to install their grips. I tried two sets of differing screws and had no issues.
  6. I’m absolutely loving this gun. My target gun was a Springfield Armory but I had a very difficult time deciding exactly what I wanted and then had a difficult time finding them in stock. So, I did research and decided to try the SDS 1911s. This gun hits way above it’s weight…it is very much comparable to a Springfield Armory Garrison (but railed). The B45R was well under $500, but has a forged frame (what other non-GI 1911s are in this price range that offer both forged frames and slides?). I basically stole a great 1911. I also don’t have any issues buying foreign/Turkish guns. I’m a 10 year military combat veteran, so I’m as patriotic as any self-proclaimed patriot, and have probably sacrificed more. ALL of my 1911s are non-US and I’ve Caniks and Tristars as well, one being my CC gun. I’ve no problem with any non-US-made guns.
  7. The plan is to maybe change/fit a silver barrel bushing but maybe in 6 months or so.

UPDATE 2:

  1. I visited the range tonight and put more rounds through the 1911 – 169 rounds to be exact. 150 of that was PMC Bronze FMJ and 19 was Remington HTP 185-gr JHP. There’s now a total of 319 rounds through the gun.
  2. One JHP failed to feed but the gun is very dirty now (haven’t cleaned it since the day I received it). As well, it choked when using one of the three GI mags I bought – the round was the first in the mag. No, 19 JHP rounds isn’t much but good JHP 45ACP ammo isn’t exactly cheap, so that’s going to have to suffice for now.
  3. I decided to test it at 12 yards out. I usually don’t shoot at distances longer than 12 yards. The gun is accurate, even in my hands (although there were flyers).
  4. The gun is tearing up my hand at the beavertail – still trying to determine how. I’m being pinched badly at the webbing of my hand where the two skin textures meet. I’ll use gloves the next range visit. UPDATE: I believe it is the back of the right-side (ambi) safety that is rubbing my hand raw. It isn’t sharp but isn’t rounded either…over long periods of time, it’s an issue. I may look into getting a one-sided safety.
  5. I’ve a Wilson Combat magazine release on the way. That should fix mag insertion problem with the WC and GI mags. No longer an issue.

UPDATE 3:

  1. I’ve shot 429 rounds from my SDS Imports DB45R 1911, thus far. Since I’ve been curious about it’s carry capabilities, I’ve been trying to shoot JHP from it, initially with mixed results.
  2. I initially shot Remington HTP 185-gr JHP, which generated several failures to feed (FTFs).
  3. Federal LE 185-gr JHP was used, as well (maybe 25 rounds), which also generated some FTFs.
  4. International Cartridge Corporation’s (ICC) 45ACP 155-gr frangible hollow points were used. For the most part, these shot without issue. That ammo can be used as defense ammo.
  5. I also fired 20 rounds of Underwood ($$$) 45ACP +P 230-gr JHP. 8 of the 20 rounds generated FTFs. I used Wilson Combat mags with this ammo. Since this ammo is expensive and since it generated so many FTFs, I will stop shooting that ammo through the DB45R. Once I suspect that the gun will shoot it without FTFs, I’ll test the ammo again.
  6. Inceptor ARX 118-gr defense ammo (non-JHP) was used, using the WC mag. There were no FTFs.
  7. I shot PMC Bronze 185-gr JHP (non-SD ammo), using the WC mag.. There were no FTFs.
  8. Hornady Critical Defense 185-gr JHP was shot through the gun, using the WC mag.. There were no FTFs.
  9. So, I now know that I can use the following ammo as viable ammo for self defense:
    ICC 155-gr FJHP
    Inceptor ARX 118-gr
    PMC Bronze 185-gr JHP
    Hornady Critical Defense 185-gr JHP
  10. In my view, the ammo problems are more than likely due to projectile ogive dimensions as well as hollow point size. If it were an issue with the gun, ALL the JHP I tested would be generating FTFs. There are no specification standards on ogive or projectile dimensions in today’s ammo market, so it’s difficult to make a gun 100% reliably eat all mass-produced ammo, and 1911s aren’t Glocks, so….

I plan to continue to shoot the PMC Bronze JHP ammo as range ammo, to continue the break-in process of the DB45R 1911.