web analytics
Categories
1911 45ACP American Classic ammo B45R JHP Metro Arms Rock Island Armory SDS Imports

My Thoughts Regarding 1911s and Jacketed Hollow Point Ammunition

One thing I’ve never done is attempt to carry a 1911. Carrying means I’ve to test JHP before committing to carrying. Everyone knows (or should know) that most 1911s don’t always readily shoot JHP.

I currently have shot 429 rounds from my SDS Imports DB45R 1911. Most of that ammo has been FMJ. Since I’ve been curious about it’s carry capabilities, I’ve been trying to shoot JHP from it, initially with mixed results.

I initially shot Remington HTP 185-gr JHP, which generated several failures to feed (FTFs).

I also shot Federal LE 185-gr JHP as well (maybe 25 rounds), which also generated some FTFs.

I documented in a previous post that I’d shot International Cartridge Corporation’s (ICC) 45ACP 155-gr frangible hollow points. For the most part, these shot without issue. That ammo can be used as defense ammo.

This past week, I shot 20 rounds of Underwood ($$$) 45ACP +P 230-gr JHP. 8 of the 20 rounds generated FTFs. I was using Wilson Combat mags with this ammo. Since this ammo is expensive and since it generated so many FTFs, I will stop shooting that ammo through the DB45R. Once I suspect that the gun will shoot it without FTFs, I’ll test the ammo again.

I shot Inceptor ARX 118-gr defense ammo (non-JHP), using the WC mag. There were no FTFs.

I shot PMC Bronze 185-gr JHP (non-SD ammo), using the WC mag.. There were no FTFs.

I shot Hornady Critical Defense 185-gr JHP, using the WC mag.. There were no FTFs.

So, I now know that I can use the following ammo as viable ammo for self defense:

  • ICC 155-gr FHP
  • Inceptor ARX 118-gr
  • PMC Bronze 185-gr JHP
  • Hornady Critical Defense 185-gr JHP

I plan to continue to shoot the PMC Bronze JHP ammo as range ammo, to continue the break-in process of the DB45R 1911.

During this round of testing, I also shot the same ammo listed above from the Metro Arms American Classic Commander (ACC) 1911 chambered in 45ACP. Note that I didn’t shoot the Critical Defense nor the Inceptor ARX from this gun, since the projectiles will almost certainly feed without issue (I tested them by chambering a round of each make, as well).

I shot most of the ICC 155-gr FHP ammo from the ACC 1911. There were initially a few FTFs, but I believe the issue was a worn recoil spring. I replaced the recoil spring and the FTFs disappeared.

I shot Underwood (again, $$$) 185-gr +P JHP from this gun, using the WC mag. This ammo was almost TOO hot, but in the gun’s defense, it isn’t as heavy as the DB45R 1911, so there’s less weight to mitigate the recoil of this hot ammo. The ammo was so hot that I had to pause in shooting the 8-round mag, since my hand was in pain. Even so, there was only one FTF, but I’m sure this may have been because the ammo was so hot that I was beginning to limp wrist.

The Remington HTP 185-gr JHP was tested the visit prior to this visit. There were some FTFs.

I also shot some of the Federal LE 185-gr JHP…there were two FTFs with that.

The rest of the listed ammo shot without issue. I’m at 520 rounds shot through this 1911, so it may be close to being broken in, which is why there’s less issues with JHP with this gun.

I also shot my RIA Rock Ultra 9mm MS 1911. I also have a RIA Tac Ultra MS 1911 which has a 22TCM barrel and spring, as well as a 9mm barrel and spring. I installed the 9mm barrel and spring for this range visit.

Both 9mm MS 1911s ran without no feed issues whatsoever. I shot several types of SD ammo, some of it JHP and some of it frangible ammo. I did have one failure to extract (FTE) with the frangible ammo when shooting the Tac Ultra, but that’s to be expected with 100-gr ammo (this ammo make was Hevi-Shot).

I was extremely impressed with the 9mm MS 1911s. I’m thinking of just carrying the 9mms instead of the 45ACP 1911s.

I’ll continue to document the testing of shooting the defense ammo.

Categories
45ACP American Classic B45R Commander Metro Arms SDS Imports

45ACP Self Defense Ammo On The Way!

I plan on carrying one of my 45ACP 1911s, although I haven’t decided which to carry yet.

I bought another Alien Gear holster and it arrived last week. This holster fits the new 5″ 1911 that I bought, the SDS 1911 Duty. I’ve never tried to carry (inside the waistband) a full-sized 1911. I tried carrying the 1911 Duty two days last week. While it is thinner than my Canik TP9 Elite SC, and carries better, but it is LONG! It is long to the point that I can’t store anything in my left right-hand rear pocket.

The Alien Gear holster is very nice and isn’t the issue. It’s just that the 5″ 1911 is longer than that I’m used to and I don’t think I’m going to be able to get used to it’s length. I’ll keep the holster anyways, just in case I decide I ever need to carry the 5″ 1911.

I’m 90% sure I think I’m going to attempt to carry my Metro Arms 1911 Commander instead. I’ve a holster shell that will fit unrailed 1911 Commanders. It is currently mounted to another Alien Gear backer and will fit the gun, but the backer is meant for smaller handguns. I’ll use it for the Commander regardless.

Before carrying either gun, I need to test SD ammo from both 1911s.

I ordered the following ammo:

  • 3 x 50-round PMC 45B Bronze 45 ACP 185 gr JHP from White Birch Armory (the same place I bought the SDS 1911)
  • 3 x 20-round boxes of Underwood 45 ACP +P 185 Grain JHP from MidwayUSA
  • 3 x 20-round boxes of Underwood 45 ACP +P 230 Grain JHP from MidwayUSA

I should be able to find acceptable ammo from the above batch, and after testing, I’ll order more for carry purposes.

I’ll keep you all updated on if there are issues with using the JHP with either 1911.

Categories
.45 .45 ACP 1911 45ACP B45R Cool Hand Gear Metalform SDS Imports

The SDS Imports 1911B45R Has Shipped!

I thought that White Birch Armory was asleep.

I’d been wondering why the order was sitting. My first thought was that they didn’t have the gun in stock. I’ve seen gun stores sit on orders, awaiting for a new shipment of guns. I was going to give them another day before contacting them to cancel the order. I also did research and other folks that bought firearms from them stated they were very prompt with processing orders.

I waited maybe 24 hours to see if the order would progress, because I needed to contact my FFL to inform them of the shipment. Well, I checked today at noon and the order was fully processed and had shipped! It caught me off-guard and I had to complete a web form notifying my FFL that a gun was inbound to them for me.

As well, they no longer have them in stock. I must’ve got the last available B45R.

The gun arrives at my FFL on 2/14 (it is currently 2/11). So, they use quick shipping too, which is unusual during Covid times, as most gun stores are using the cheapest shipping possible and it’s usually USPS, which is slow 90% of the time.

Even when the gun arrives on Monday, I still have to await the FFL to contact me so that I can make an appointment for pickup. When I pick it up, I will try to shoot it before I leave (my FFL is a range/store).

I also bought some things for it, but those will probably arrive later in the week.

I bought 3 sets of full-size 1911 grips (I couldn’t decide on one type and I’ve other 1911s that I can install those grips on). One is a set of dark red wood grips with gold screws that may look nice on the black 1911 – they might be slick, though, so I bought an extra set that I can use for range duty. The site I bought from was Cool Hand Gear.

I also bought a 3-pack of full-sized 45ACP Metalform mags with flat base plates. They are GI mags. I need more mags anyways and I think flat base plated 1911 mags look good in certain guns. I bought these from eBay.

I also thought to buy a new recoil spring, just in case I need it, but I think that can wait a bit.

I’m also thinking I will eventually want a silver barrel bushing (the one on the gun is black)…the silver will match the silver of the trigger blade.

Categories
.45 ACP 1911 45ACP

My Annual Purchase For 2022

I usually try to buy a gun a year, specifically around this time. Last year, I bought a RIA 10mm 5″ double-stacked 1911 and Canik TP9 Elite SC. The year before that, I bought nothing. The year prior to that, which was the year I started making this an annual experience, I bought the PSA AK-V and AK-P.

I’d planned on getting another AK and had my eye on a 5.56/.223 variant but had a number of problems committing to another AK.

For one, higher end AKs are difficult to find in stock and when they are in stock, they quickly become out-of-stock.

Secondly, I’ve one pistol caliber AK pistol, as well as an AK pistol chambered in 7.62×39. I also have two AK rifles (both in 7.62×39). I’d wanted a 5.56 AK but couldn’t decide on if I wanted yet another long gun or pistol chambered in that caliber – I have both types already. I wouldn’t have cared but when I asked on the AK subreddit, the absolutely stupid replies back soured me to any AK, so I ended up not no longer wanting an AK.

I then decided to focus on a higher end 1911, either a mid-grade Sig or Springfield Armory. In fact, I wasn’t really caring on a particular 1911 maker. I just wanted the product to have a forged frame, slide, and barrel that was 5″ max with a traditional barrel (ie, no bull barrel). Price was $1000 max with a focus on lower price. I couldn’t find much that was in stock. I saw a LOT of Springfield Armory Garrisons but I wasn’t liking the sights on those (I wanted fully adjustable front and rear sights).

I’d been looking for weeks and couldn’t find much. I even looked outside of 1911s (looked at Sig’s P320 AXG Classic and Equinox – they were all expensive as hell). I’d also looked for the Springfield Armory SA-35 but they’re definitely out of stock everywhere.

I then decided to look at any 1911 that had forged slides and frames. I became focused on the IWI Desert Eagle 1911s until I saw that their frames are cast (precision cast but still cast).

Then I remembered that some of the Turkish 1911s had forged frames and slides. I focused on SDS and Tisas (SDS imports Tisas, I believe).

I found one that was discounted to $439 and tried to buy it but changed my mind right before I committed to the purchase because the website seemed fishy (it was http://www.2agunshow.com). The website seemed “sketchAF” and the price was super cheap, undercutting the next lowest 1911 of the same make/model by close to $40. Also when I tried to select an FFL at my location 5-10 miles round me, none of the usual FFLs showed in the results…it was very odd (maybe affiliated with dealers if it wasn’t actually sketch).

This gun was also listed at $432 here but went out of stock maybe 10 min after I saw it..

I ended up going to that next lowest priced gun of the same type and paying a bit extra for it (after researching the website/store first to ensure it was a legit site for regular buyers). I bought it.

What did I buy?

I bought the SDS Imports 1911DB45R – Duty w/ Rail 45ACP 5″ Black Cerakote. It’s a nice gun. I saw a better looking version but opted out of it because it was 4.25″ – I wanted a 5″ 45ACP 1911. The gun was $470.

A question that someone is going to ask, either at my Youtube channel or here, or even in the back of his mind when reading this: How in the hell did you go from Springfield Armory to a cheap Turkish gun?

That’s an easy question to answer. A true gun enthusiast will be acutely aware of Turkey’s history of gun-making and this particular brand, which is Tisas. Most uneducated folks think “cheaply made with non-quality materials and bad fitment/finish” when anyone mentions guns made outside of the US and 1st World countries in the EU. It’s a generally ignorant mentality. I’m not even sure Turkey can be considered a 3rd Word country. It’s like folks are thinking Afghanistan when thinking of Turkey! Folks familiar with Tisas-made 1911s know that they are quality. There are many models of US-made 1911s that are still using cast frames and many $1000+ 1911s are still using MIM parts. This particular 1911 has a forged slide, barrel (which even extremely cheap and shoddily built 1911s will have), and a forged frame. I don’t think ANY 1911s currently under production and under $500 have all three of those forged parts, with the exception of Tisas 1911s. Not only that, the fitment and finish of this gun equates more to $900-1000 1911s. If someone handled and even fired this firearm (but was withheld the make and country of origin), I bet they’d heap praises on it. And if they were made aware of the material makeup of the firearm, they’d further pile on the praises. When people know it’s from Turkey, they are immediately blinded and will actively refuse to further consider the gun. When I see this, I immediately have a general idea of their thought processes. “Buy only American products.” “Why would you buy something cheaply made when, for a few dollars more, you can have a Springfield or Sig?” And, it sometimes gets uglier: “Why would you support terrorism by buying a Turkish gun?”

Turkey is a NATO partner and the company named Tisas isn’t operated by the Turkish government. Yeah, no one likes Ergodan, but that doesn’t mean all companies in Turkey have Ergodan’s mentality.

While the price of the gun may be budget-minded, the makeup of the gun itself is pretty nice. I’m getting forged parts and the gun has little MIM parts (while all Springfield Armory 1911s are full of MIM). The Tisas 1911 was the better gun.

Also, going cheaper leaves me with some money for more ammo and options to upgrade the sights (I’m pretty sure the gun will come with contrast non-adjustable sights).

I will also probably buy another gun too, since I originally wanted to spend up to $1K. It will more than likely be an AR pistol chambered in 9mm – that’s something I don’t have. I will almost certainly buy a blemished one from PSA. I’ll post more about that later.

UPDATE (12/13/2023): The only MIM part in all Tisas 1911s currently produced is the recoil spring plug, and that can easily be replaced with a non-MIM part, without the need for fitting that part. They started doing that late 2022, I believe. Pricing has crept up, but Tisas are still the only guns under $1000 that have no MIM.

Categories
1911 1911A1 45ACP 9mm American Classic Commander Metro Arms RIA Rock Island Armory

New YouTube Video – 1911 Range Day!

I tried a new format in this video, using my GoPro hat-clip. What I didnt’ account for was the volume isn’t crisp, as the hat-clip requires usage of the GoPro case, which is apparently covering the camera’s mic. 🙁

There were issues with the Metro Arms 1911. I’ve been suspecting as much the past 1-2 years, but my handgun experience is expanding and I’m confident to say that this handgun has issues with it’s sights. I’ll be looking into obtaining a new set of sights for this handgun (I wouldn’t mind having the sights that are on my RIA Tac Ultra installed on this handgun).

Also, I finally installed the 9mm barrel into my RIA Tac Ultra (I have always shot it with the 22TCM barrel installed). I shot 140 rounds of 9mm from the gun. The gun now has a total of 746 rounds through it. It’s my third most-fired handgun (the Grand Power P11 and Bersa Thunder Plus are 1st and 2nd).

There were some fails to feed when firing the Tac Ultra, but the feed issues only occurred with the OEM mags. I’ve Wilson Combat 9mm ETM mags, which didn’t have any feed issues. I also used the 38 Super mag that came with the Tac Ultra. I also used the 9mm mag that came with my RIA Rock Ultra. The latter two mag are the mags that had inconsistent issues. The feed issues were occurring mid-mag.

Lastly, I need to research who is the new US importer for Metro Arms. Eagle Imports was the importer, but they went out of business earlier this year.

Categories
1911A2 45ACP base plate Century Arms magazines R1 Remington

Looking for mags that fit your RIA 1911A2?

When I bought my RIA 10mm 1911A2, I tried to order A2 mags from AdvancedTactical.com (Armscor parts/support site).  The showed as having plenty in stock but apparently, they were out, because my order sat for a month before I told them to cancel it.  In fact, they’re still showing as out of stock at the time of this posting.

I tried looking at other places but most stores are out of stock.  The only stores I saw that had them were in places like Alaska and Canada and they required $100 in purchases before they’d even consider sending to you (shipping was free, though).

I then saw in a 1911 FB group where a guy stated he’d bought Remington R1 .45ACP double-stack mags and that the mags latched into the gun.  The mags fed ammo reliably into the handgun.

I decided to seek out that magazine type.  Again, I had a difficult time finding a place that had them in stock, but I finally found that Century Arms carries them.  I ordered two of the mags on 3/9.  It is now 3/18 and they’ve arrived at my door.

The first mag latched without issue, but the second one initially would not latch.  Ground the top of the mag’s catch hole just a tad.  It now latches.

Both fit without issue, although latching is pretty tight…this can be fixed by ordering thinner base plates (or slightly grinding the top of the catch hole on the mag).  The mags are designed for 45ACP and will hold 16 rounds of 45ACP.  I loaded one mag with 10mm and was able to load 18.

I will be visiting the range tonight or tomorrow to test feeding/functionality with both mags. I’ll test with 16 rounds as well as 18.

These mags are $9-$10 cheaper than the mags Armscor sells and they appear to be more readily available.  I’ve been trying to get mags since 1/31 and Armscor went out of stock around that time.  I could find Para mags but didn’t want to hack/cut/file a mag.  Granted, I had to grind one of the mags I bought, but it was a 10 sec grind where you wouldn’t even notice an alteration.

The base plate on the R1 mags are rather thick.  They protrude from the magwell a bit, but they can be changed to something less thick (or they can be ignored for shooting purposes).

OEM magazine
OEM magazine
R1 magazine
R1 magazine

As of 3/9, Century Arms had them in stock.  I’m not sure if they’re still showing as in stock but if you need 1911A2 mags for your RIA, Century Arms is currently the place to visit.

UPDATE (3/19/2021):  I took off the base plate on the OEM mag to see if it’ll fit on the R1 mags.  It does.  So, if you buy the R1 mags, you can buy OEM base plates from Armscor and fit them on the R1 mags.

UPDATE (12/21/2021): Century Arms has stopped carrying the Remington R1 double-stack mags.  🙁

Categories
45ACP Mod.2 Springfield Armory sub-compact XD45 XD9

I Bought a Subcompact Chambered in 45ACP!

So, I’d been thinking about larger caliber handguns lately, and love my XD 9 subcompact.  I’d heard great reviews on the XD 45 variant.  I found a used XD 45 that was being sold for $329.  After shipping and taxes, it was priced at $389…still a steal!  I bought it this past Sunday.  It should arrive at my FFL on Saturday.  Due to that, I might have to wait until Sunday or Monday to pick it up.

The handgun will come with a 9-round and 13-round magazine and nothing else.

While I’m excited about the handgun, I’m a bit miffed about the shipping.  The damned gun is in-state.  The store that sold it to me is in Virginia Beach.  I’m in the Manassas area.  I could’ve driven to pick it up and saved the $50 in shipping (at least).  I bought it on Sunday night via Gunbroker.com.  They wanted an over-the-phone transaction so I called them Monday morning when they opened.  I’d already contacted my local FFL (my range) so they were aware of the purchase and incoming firearm.  I asked them to send their FFL info to the store where I bought the handgun.  I think they sent their FFL info to the store either late Monday or Tuesday morning.  I got an email from USPS stating that the gun was due to be shipped but hadn’t been picked up yet…that was Tuesday morning around 10AM.  The firearm sat a the store all day…wasn’t picked up until late that evening.  It’s due to arrive 12/15.  That’s 3 days for transport when I could drive to that store and be there within 3 hours (max).  WTF.  Most people would blame the shipping (USPS) but I’ve bought firearms from out of state that didn’t take 3 days to arrive at the local post office.  I know shipping can be expensive for a business but shit, didn’t I pay $30 for shipping?  That shipping fee results in the slowest mailing method?  That’s B.S. IMO.  I won’t be buying from them again.  And, this is a mom/pop, brick-mortar store.  People always harp on supporting local and/or brick-mortar stores but when crap like this happens, I hear nothing but crickets.

Anyways, I’m going to be using my XD 9 subcompact Alien Gear holster for the XD 45 since I hear they’re compatible with the holster.  I’ll probably end up buying 2-3 extra 9-round mags as well.

The plan is to carry this handgun.  I’ll keep you all updated as I become familiar with it.

UPDATE (12/15/2018):
She has arrived, and two days early (picked her up at 8:30AM yesterday before heading to work).  Was not able to shoot from her since I had to go straight to work.  Will try to take her out today — getting dressed now, in fact!

UPDATE (1/1/2019)

I’ve done a quick review here:

Categories
1911 45ACP 9mm extractor FTE FTF HTP light strikes Remington

Metro Arms 1911 Fixed, 1911 Trigger Pull Issue

I went to the range for a quick visit today. I brought two 1911s this time:  my RIA midsized 1911 in 9mm and the Metro Arms AC Commander 45.

The first thing I did was fire 50 rounds from the 1911 that was a solid shooter (the 9mm)…it ate all the ammo without issue, but at first I was shooting very low left with it as well.  See the picture’s captioning.

I started at the left corner, then went to the right corner, then stopped because I wasn’t hitting point of aim (the red).  When I did very slow trigger pulls when aiming at the center target, I hit point of aim.  I’m having issues with the 1911 trigger…it wasn’t the Metro Arms that was the issue.  That was at 7 yards.

I then began to focus on my trigger pull. I still had trouble trying to figure out which part of the finger to use, but I found that if I shot slowly, I was dead-on. I went through most of a box of ammo pretty much hitting point of aim. It’s an issue of me not being used to the trigger mechanics of a 1911.

I also had two light strikes, which was weird…I’ve not had such issues before.  They both fired when I reloaded them into the mags.

Ammo was Remington UMC 115-grain FMJ.

I then went to my trouble-maker 1911. I had no issues aiming after my 50-round session with the 9mm 1911, although my hands were sweaty and I ended up using gloves.

This is MUCH better than my last range visit, when I was hitting very low left and not being even close to center target.

I also shot 49 rounds of Geco 230-grain FMJ without ANY feed/extract issues. There was 50 in the box…yeah, I had one issue where the round didn’t extract (this is a first…this gun has an exclusive history of not feeding properly). But one in 50 is NOT bad, especially when I was having feed issues several times (ie, 2-3) with each magazine. I think the extractor needs to be replaced, but the tuning I did on it helped a LOT!

So, I’m glad I sorted these issues out.  I think I’ll put the 1911s away for a while, because they don’t shoot like my other guns and I don’t want my muscle memory getting mucked up.

Oh yeah, I decided to shoot some extra ammo I had sitting around (Remington HTP 147-grain JHP subsonic).  I shot 50 rounds of it through my Grand Power P11.  The P11 did NOT like that ammo at all.  There were lots of failures to return to battery, so much that I was hitting the back of the slide almost as much as I was pulling the trigger.  I thought that HTP wouldn’t be as bad as UMC…I was wrong.  I need to remind myself to not shoot Remington out of the Grand Power.  EVERY time I do, I’m disappointed.

Categories
1911 22TCM 45ACP fail to extract fail to feed JHP TulAmmo Winchester

Recent Range Visit

Last night I visited Elite Shooting Sports to shoot my .22TCM MS 1911 and Metro Arms ACC .45ACP 1911.

First, I started out with the .22TCM 1911.  I was immediately accurate with it (well, accurate enough considering I’d not shot it since April 2015, I was shooting it pretty well):

From 7 yards

I then moved the target out and focused on the head:

From 10 yards

I then moved to the .45ACP and didn’t fare as well.  The last time I fired this handgun was Feb 2015:

7 yards out

The recoil took me aback.  Now, when I first shot this gun, it felt great in my hands.  For some reason, it didn’t feel great this time around, but this could be because I’d just shot the .22TCM 1911, which has VZ grips.  It could also be because I’m more used to 9mm now (this gun has substantial push/recoil, even with it being a beaver-tailed).  Here’s more:

I stayed 7 yards out, since I was having issues putting lead onto the bulls-eye

I can’t understand what I was doing wrong.  Yes, I’m aware of target analysis and what it means when I’m grouping to the lower left of the target.  I actually took my time with several magazines to ensure I was properly actuating the trigger, but I was still hitting lower left.  Although I was able to touch the bulls-eye, I wasn’t able to do it consistently.  I couldn’t hit the head of the target, either.

I was using TulAmmo and Winchester white box JHP.  The TulAmmo was inconsistent, power-wise, as I noticed that the slide moved slowly many times, so I switched to the Winchester and noticed less of that, but only shot maybe 25 rounds of it.  I still wasn’t hitting where I wanted, but at least the slide was acting normally when the gun went BANG.  Another thing — this gun does NOT like TulAmmo.  The ammo kept hanging on the feed ramp.  I didn’t notice this when I first shot it back in February.

Here are my range notes from February:

Half of the ammo was Remington UMC (green/white box).  47 of it was Perfecta FMJ.  I had 3 x FTEs with the black (original) mag.

This gun is FUN to fire!  The recoil is much less than the P220.  It is also very controllable, aim-wise — I nailed the bulls-eye several times and the majority of my hits were toward the middle when compared to the groupings of the other guns I’ve fired.

Back to this range visit.  The Winchester JHP did fine, but TulAmmo is dirty as hell…the feed ramp was heavily covered in carbon.  I can polish the feed ramp but I won’t.  I just won’t shoot TulAmmo as defensive ammo…that’s the best solution.  It’s the ammo, not the gun, and since this is practice ammo, it’s all good.
 
Very odd failure to extract situation here…I had to drop the mag to clear it (it wouldn’t rack back).  
 
I had several FTEs in Feb that I attributed to a possible mag issue.  I think that was a wrong assessment, since the mag would have nothing to do with any problems after the round has been fired.  I also had several FTEs with this range visit (2-3).  All of it was with the TulAmmo.  None of the Winchester FTE’d.  A friend suggested I was limp-wristing.  I don’t think I’ve ever limp-wristed a big caliber handgun before…I don’t think it’s happening now, either, but I’m not sure how to test for that, but like I said, none of the other ammo failed to extract.  I’m going to attribute this to the the TulAmmo.

 

Lesson learned – don’t shoot TulAmmo from this gun!

Notice in my notes that I had no issues controlling the gun, I was able to nail the bulls-eye several times, and most of the rounds were hitting toward the middle.  What has changed?  The ammo?  My perceptions on this gun’s recoil?  I’ll admit, when I first pulled the trigger, the recoil caught me off-guard (I’m used to firing 9mm).  It could’ve ruined the rest of my session with this gun.  Should I keep practicing with it?  I’m not planning to carry any of my .45ACP handguns, so it’s not essential that I train with this particular gun.  It’s a range gun, for now, but it does bug me that I can’t put lead on target with this gun like I can with my other handguns.  I just might change the grips, though (to a set of VZ grips).

And then, when I went back to my .22TCM, I found that I couldn’t hit anywhere near where I was aiming, when I had such a good session with it at the beginning of the range session.  I fired 25 rounds before deciding to quit for the night…I left the range in a bit of a fog.  I’m not sure why my aim was so jacked up after switching up guns…maybe I was slapping the trigger or maybe I the gun wasn’t properly centered in my hands…I don’t know.

 
 
 
 

 

Categories
45ACP P320 Sig Sig Sauer

SIG Sauer released the .45ACP P320!

SIG has released the .45ACP version of the P320! I guess I need to eventually get the conversion kit for my P320 Compact.

UPDATE: Bad news…there will be no .45ACP conversion kit! 🙁 Apparently they’ve run into design issues and can’t make a .45 conversion kit, although they’ll make the pistol itself (it just won’t convert to other calibers). You’ll still be able to change frames and such, though, from my understanding. More info is here.

NOW SHIPPING: The P320 in .45ACP. Oh, yeah. #P320
Posted by Sig Sauer on Wednesday, May 6, 2015