Categories
1911 2011 Springfield Armory

I’m The New Owner of a Prodigy DS Compact!

I neglected to update the blog to say that I have received the gun and have shot it.

This whole transfer experience was outstandingly great. The shipper, Gunprime, was quick in shipping the gun where I needed it to go. I’d never used my range as a receiving FFL, so I was anxious to see how that experience played out. My range received the gun and notified me within 2 hours that it was ready to be picked up, which was something I’ve never seen before. In my experience, receiving FFLs typically sit on the gun. In many cases, I’d wait 2-3 days in the past to get a call from receiving FFL that the gun was ready to be picked up, and in some cases, I had to make an appointment that was usually the week after it arrived to them.

When I went to pick up the gun, the transfer experience was pretty cool. There was no paper involved. Everything was done on e-forms, on a laptop. I’d fill out the e-form, and the range employee would look it over and ask me to make any corrections (or not). I did both forms in that manner and process took the same amount of time as if I’d done it on paper. And the background check results were done 5 minutes after submittal.

To top all that off, the transfer fee was a total of $17!

So, I got home and ended up racking the gun maybe 100-130 times while watching TV with my wife. The gun is stiff AF.

As it is my first Springfield Armory 1911/2011, I wasn’t sure what to expect. The gun is clean. Fitment and finish is good. Grip texture is great. Both mags are good. I ended up ordering three more, for $37 each – note that MSRP on those mags are $60 apiece.

The gun fits in my current 2011 holsters (but I haven’t tested the QVO IWB holster since it keys off the gun light and the only gun light that I have is currently on the Ultralight).

Some things I don’t like:

The optics plate adapter that comes with the gun — I’m not sure why they insist on sticking with including the Docter plate with Prodigy handguns…IMO, that’s a seriously stupid choice of footprint, especially when most folks are going to end up having to buy another (they’re not cheap, either – $120). When I went to the SA page to order one in RMSc footprint, they were out of stock (WTF). In fact, they’re kinda scarce. I ended up ordering one from eBay (for $119).

Also, the right thumb safety is pinching the hell out of my hand when disabling the safety, unless I purposely shift my hand a certain way. I will either have to try to swap in a single sided safety, grind the stock right-side lever so that it won’t pinch me, or pay a gunsmith to sort it out for me.

The trigger measures at (an average of 5 pulls) 3 lb 8 oz but feels heavier. As with my experience with my Tisas DS, the trigger wall feels heavy.

Lastly, the gun feels seriously oversprung. I don’t want to mess with swapping springs, as I just received the gun and I don’t want to start swapping parts so soon. It may break in.

How does it shoot? I’m shooting left of most of my bullseyes – 1 inch left at 7 yards and 2-3 at 10 yards. I think it’s due to the trigger wall…as I’m negotiating the trigger, I’m inadvertently pulling my point of aim. With the Tisas DS, I waited until 500 rounds before I lost my patience and swapped in a different sear spring. I will do the same with the Prodigy, although I could just tweak the OEM spring, which may help.

The gun doesn’t feel snappy, probably due to the great grip textures – the Bul Armory Ultralight feels a lot snappier (probably due to lack of good grip texturing).

I shot 120 rounds through the gun before I ran out of range time. The gun didn’t choke or misfeed and the gun was dirty – I didn’t clean it, as I was working with limited time.

At some point, I need to try JHP through the gun, as I keep seeing folks saying that their Prodigy Compacts are experiencing feeding issues. I think that I should wait until maybe 500 rounds before I try JHP, as that will give the gun’s parts time to wear in.

Categories
1911 2011 9mm double-stack Springfield Armory

Will Be Picking Up Prodigy DS Compact This Evening

This gun came to my FFL in record time.

I ordered it from Gunprime LATE Thursday night. Gunprime processed it Friday around noon-ish and UPS picked it up that afteroon. UPS usually processes gun on a 2-day timeline, so, Monday and Tuesday were the transport days and they delivered it today (Tuesday around noon).

I was ready to wait for XCal to take a day or two to process it, but they sent me a text a few minutes ago saying it was ready for pickup. Wow! That’s exceptional, time-wise.

So, I’ll be heading out to XCal after work (maybe 6 or 6:30 PM) to do the background check, which shouldn’t take all that long to do.

As I’ve never used XCal as an FFL, I’m not sure what to expect. One thing that annoys me about FFLs is that I’ve been to more than a few that want you to process the background check without even looking at the gun. The problem with that is that the gun could have flaws (gun won’t cycle, or gun has massive scratches, for example) or might not have what was purchased (a mag, for example)…if they won’t let you see it and you do the paperwork first, it’s your gun, literally sight unseen. The gun isn’t yours until you perform the transfer (from FFL to you). Prior to that, the gun is being transferred from FFL (store) to FFL (store).

So, yeah, I’m excited. I also ordered three more mags from LockedLoaded.com, as they had them on sale for $37, vs the MSRP cost of $60 each.

I also scheduled a range visit for Wednesday evening…I’ll perform an initial assessment of the Prodigy DS then.

Categories
1911 2011 9mm Springfield Armory

I’ve a Prodigy DS Compact on the way to me!

So, I just completed the order of the next gun.

I had a seriously bad time trying to determine what guns I wanted this year.

I’ll be buying two within the next 30 days.

I just bought a Springfield Armory Prodigy DS Compact 3.5″, from Gunprime. I’d initially planned on buying the 4.25″ Compact but I do a lot of bending and squatting and when carrying AIWB, tasks such as tying shoes is sometimes difficult. I’ve carried Commander 1911s AIWB in the past, but it’s been a while. I was about to order the 4.25″ when I decided to keep it short, since I plan to replace my Bul Armory SAS II Ultralight with the Prodigy Compact.

I’m 100% sure the next gun that I’m buying is another Springfield Armory – I just don’t know which one I’m buying. It’s either the Prodigy 5″ (maybe Comp) or the 5″ Emissary AOS in 9mm. As I don’t have a full-size 1911/2011 in 9mm, I’d initially wanted a full sized prodigy, but the 5″ Emissary is BEAUTIFUL! I was locked onto a 5″ Prodigy Comp until I remembered the Emissary. There’s a very high chance I’ll end up getting the Emissary.

So, the wait is on. I’ve never ordered from Gunprime before, but I’ve been aware of them and have looked at their stock of guns in the past. I’m not sure how prompt they are in processing and shipping guns. There are several popular gun stores that I avoided because they insist on a 5-10 day processing regimen…that’s BS…yeah, I know they’re busy but waiting 10 days to have a gun processed is quite lame. What the hell – that’s like two business weeks!

Knowing my luck, this gun will come when I’m away. I’ve business in CA and will be gone week after next. I ordered this gun late Thursday night (3/20). It might not even be looked at until mid-week next week, and I fly out 3/29 and will be away a full week. That’s how my Ultralight came in – I got a call when I was fishing 300+ miles away. We’ll see how this plays out.

I’m excited but not excited. I know the Prodigy will be good, but it’s probably going to be similar to the Ultralight (not a bad thing exactly). Really, I just need it to be dependable and for ALL the controls to work – the Ultralight’s grip saftey doesn’t function properly (trigger can be dropped without touching the grip safety, although I’ve to hulk up a bit on the trigger). Bul Armory has had the UL twice but can’t (or won’t) fix the grip safety. I think they fucked up the gun when hand-fitting the grip safety – I think they may’ve removed too much material. When metal is removed, it can’t be returned (unless you weld more metal onto the part), which is probably why they’ve had a hard time fixing the issue, although I asked them to replace the part before I returned it the 2nd time, which they did not. I’m not even sure what they did to “repair” it, as the grip safety looked the same as before I sent it back to them, and the saftey was functioning for maye a month before it stopped working again. This is why I won’t buy another Bul Armory – they won’t stand by their own workmanship. I’ve never heard of Springfield Armory doing such a thing, and I’ve never owned a higher end Springfield Armory gun (I’ve two XD9 Mod 2 guns, though).

Of course, I’ll post here with initial thoughts and pics/videos once I’ve received the Prodigy Compact.

UPDATE (3/21/2025): It’s already shipped…Gunprime FTW! It’s supposed to be delivered early morning on Tuesday, via UPS. This is good. I do not know the receiving FFL’s policy on transfers (not sure how long I’ll have to wait for them to process it). They receive it on 3/25. I fly out on 3/29. That’ll leave 3/25 – 3/28 for them to process it. The earlier the better, so that I can have a day or 3 with the gun before I fly out. I’ve not used my range for a transfer since I’ve been a member (2+ years). I’ve been using a different store for that, but my range’s transfer fees are cheap, and I get a discount as a member. I’m curious how this will go, and excited, as well.

Categories
1911 2011 Optic range visit Tisas

My Thoughts on Using my First Closed-Emitter Optic

I visited the range yesterday, with the Tisas DS9 Carry. The plan was to zero the Viridian RFX45.

I spent maybe 40 minutes zeroing the optic – because Viridian’s instructions were backwards. Once I had the optic zeroed, I began to shoot to test out the optic…during the testing (all 10 min of it), the optic screws started backing out. I wasn’t initially aware, and I’d been tweaking the zero, so the optic’s current zero may be out of whack. I’ll address that at the next range visit.

The slide was hot, and because I was giving the gun the beans, I’m thinking the heat loosened the thread locker, and since the screws are so short, there wasn’t much thread locker on the screws.

I ordered more screws maybe 2-3 days ago (I stated that in my last post). They’ll arrive on 3/10. These are the M3-0.5 x 6mm screws. The gun is currently using a pair of M3-0.5 x 3.4 mm that were included with the optic. I’m now doubting that the 6mm screws will be long enough, so I ordered another set from eBay (8mm)…they should be here within 4 days.

I do have some longer screws that I might be able to cut down with a dremel…they’re too long – I tried using them and they bottom out before they start securing the optic.

Other than all that, the optic is great! Some observations:

  • The optic’s front glass got dirty quickly, much more quickly than my other optics, but none are as close to the ejection port as that optic/gun combo.
  • Brass was pinging off the optic’s frame, on it’s right side. I sort of expected this, as the prior optic I used on this gun (Cyelee CAT) was also catching brass.
  • The glass offers a much wider field of view than I’m used to, which is good.
  • I’m able to shoot the gun quickly with the optic, while still being accurate (at 10 yards, too).
  • As mentioned earlier, the zeroing instructions that Viridian supplied had me moving the damned POI to the edge of the paper target, which was frustrating.
  • Would love for this optic to have a two reticle system, as my Holosun ACSS Vulcan does…I may be spoiled by that double reticle system, as I was struggling to find the dot whenevev I was trying to look down the sight.
  • Cowitness of the irons look to be a bit less than 1/3rd, but is still more usable than when trying to use the integrated iron on the Holosun 507K with my Ultralight.
  • Due to it being a closed emitter optic, it’s super easy to clean off the carbon and fingerprints.
  • The Acro footprint is pretty badass. The two screws that hold the adapter in place will loosen well before the one screw that holds the optic onto the adapter.
  • One thing I don’t like about this optic is that it’s so big that I’ve to grab it behind the optic when racking, which is a PITA. I do not like racking a gun by grabbing it’s optic and I refuse to do it. Luckily, this is a setup I don’t plan to carry.

Based on my observations, I just might try to pick up an RFX44…it’ll sit better on an RMSc-cut slide than an RFX45 would on an RMSc-cut slide, for sure.

I love the RFX45 because I’m getting a lot of bang for the buck…the optic wasn’t super expensive because I found it for a good price (much lower than MSRP), but I’m getting a lot from it. Because it has all it’s innards up top within the optic, it sits low on the gun, which helps with cowitness.

I may try to visit the range again this coming Wednesday (my work day – I work not far from my range, so it may be easy for me to visit after work). If not, I’m also off on Friday (my birthday is Saturday). I think I’ll try to schedule Wednesday AND Friday.

Categories
1911 2011 Optic range visit Tisas

I Mounted The Viridian RFX45 To The Tisas DS Carry!

A few weeks ago, I bought a Viridian RFX45, knowing it’s mainly an optic that won’t fit RMSc-cut guns. I bought the optic for use with a few duty-sized guns that I’ll be purchasing…those guns are cut for RMR sights.

I then wondered if this particular optic will fit a Tisas DS Carry (I’ve the Gen 1 version). They are cut for RMSc (the new gens might allow for RMR, though). Looking at the RFX45, it’s quite a bit longer than a typical RMSc optic, so I doubted I could fit the RFX45 to it. This is also why the RFX44 exists, as it is a mailbox-type of optic that fits guns that are cut for RMSc. I didn’t want to buy the RFX44 because it’s specs are inferior to the RFX45.

So, I decided to see if I could get it to fit, knowing I might be unsuccessful.

I bought an RMSc-to-Acro adapter plate and it arrived today.

I removed the Cyelee CAT from the Tisas DS Carry and test-fit the adapter plate to the gun…it fit right onto the gun without issue.

I then wanted to see how the RFX45 would mount to the adapter plate. It fit onth the plate without issue.

The biggest problem for me was finding screws. I had to use M3-0.5 x 3.4mm, as those were the only screws I had that would fit. I’d other longer M3 screws but they were too long and wouldn’t even put tension on the plate. The M3-0.5 x 3.4mm screws are super-short but they had thread locker and I had enough length to secure the optic. I also decided right then to buy some M3-0.5 x 6 mm (I believe 6mm will fit). They’re on the way to me now.

So, with the short M3 screws, the adapter plate was able to be properly mounted to the gun’s slide. From there, all I had to do was clamp on the optic (I love the Acro pattern).

The adapter plate lifts the optic so that it sits above the milling, otherwise the optic wouldn’t be able to fit in the smaller footprint. I also still have cowitness of my irons.

Note that the RFX45 is a closed emitter optic. It has a large viewing port. It’s also a green dot (all Viridian optics are green).

I absolutely can’t wait to test this setup at the range. I’ve a scheduled range visit tomorrow evening.

Some pics are below. Yeah, the gun is dirty – I use my guns.