Tag: Bul Armory

Categories
2011 9mm Bul Armory SAS II Ultralight

The Saga of the Non-functional Grip Safety, Part V

I’d posted about my non-functioning (or intermittently functioning) grip safety on my Bul Armory Ultralight.

I wanted to provide some updates.

I was previously a Patreon member of Graham Baates’ YouTube channel. Not all that long ago, he was touting that Bul Armory’s customer support was great. I then mentioned to him that I’ve little faith in Bul Armory. I explained everything that occurred with my Ultralight’s grip safety.

He asked if he could reach out to them and ask questions, hoping to see if they’d resolve the issue. I should’ve refused, but didn’t want to pass up the opportunity.

He reached out to them, providing my point of contact information so that they could reference the support case. When they replied back, I was more than a bit put-off.

Here’s what he forwarded to me:

I heard back and what was reported was that you must have removed the mainspring housing pin (maybe to remove the magazine well?) while the hammer was backand so the internals jettisoned, and it appears they were sort of forced back in place without proper alignment. Is that accurate?

I got hot, quick-fast. I’d communicated with them in the past regarding this issue and they didn’t reply back in such a fashion.

This is all but blaming the customer regarding a non-functional safety! Think about it for a second.

They implied that I didn’t reassemble the gun properly, which stopped the grip safety from working. That’s all but impossible to cause by disassembling and reassembling the firearm.

When I grip safety stops working properly, it’s almost certainly due to the part not being fit properly. To be clear, it’s usually due to the part being over-fit, by a gunsmith. I’m sure they may wear down over time, but I’ve only owned the gun maybe 3-4 years. It only has 2300 rounds through it.

There’s no way this could occur by a misalignment when reassembling a detail-stripped 1911.

I’ve 8-9 other 1911s and 2011s besides the Ultralight. I’ve detail stripped all of them, more than a few times, as well. None of them have that particular issue. Only the Ultralight has that issue.

If I were to believe them, that would mean that the tolerances on the internal parts of that gun are either very malleable, or it has some unwanted tolerances that would allow the grip safety to move. If that’s what they’re saying, that’s crazy to admit.

Detail-stripping and reassembling a 1911 isn’t rocket science or a black art. It’s super easy to both disassemble and reassemble. There’s no other order/method of reassembling a 1911. When reassembling, you can’t get it so wrong that a grip safety drops the hammer without the grip safety being touched. That is a fitment and/or metallurgy issue.

Basically, if too much material was removed from the grip safety’s internal arm (or lug), it might not reliably block the trigger bow even when the safety is fully released.

Additionally, a tight fit between the bottom of the grip safety and the top of the mainspring housing can cause the safety to bind or stick, preventing it from moving freely regardless of the gun’s round count.

There are other things that can cause the grip safety to malfunction, too – sear spring tension, trigger bow interference, debris, bad pre-travel adjustment, and changes of grip technique (that last item isn’t a mechanical part issue, though).

None of the issues are due to mis-assembling. And yes, I checked pre-travel (Bul Armory probably did, too).

I apologized to Graham the next day but never took the time to explain how to Graham how I explained it up above.

I will never buy another gun from Bul Armory. Even before Graham tried to assist, I was unlikely to purchase another gun from Bul Armory, but they’re reply pretty much solidified my decision.

What’s funny is that I asked them to replace the grip safety twice when I sent the gun back to them for repair. They never replaced the grip safety. I’m almost certain they only bent the right leg of the sear spring to add tension, which is a temporary fix – that tension will eventually loosen, which is why the issue keeps recurring. They applied the lazy fix, twice, and then had the gall to tell me that I was reassembling the gun wrong.

Research tells me that the grip safety needs to be replaced. I’ve also asked other 1911 owners and got the same feedback.

As I stated in the past, I eventually plan to either block the grip safety and only use the gun as a range gun, OR, hire a local gunsmith to install a new grip safety.

Categories
1911 2011 9mm Alpha Foxtrot Attila double-stack

My Thoughts Regarding Alpha Foxtrot and the Attila

I’m still in the process of shooting 1000 rounds through the Alpha Foxtrot Attila. I’m at 702 rounds, so far.

What I’ve been wondering is, why is Alpha Foxtrot not sending T&E Attilas to the firearms press (press and influencers). I think that’s odd, because they’ve been doing it with their other guns – the Romulus and AF S15.

I wonder if they’re having issues with this gun, to the point that they’re not sending the gun to influencers to review. If things were that bad, you’d think they’d not have them within public circulation. I’m not sure things are that bad, but AF not sending out test guns is odd.

As well, there were no YT entities reviewing guns that they actually bought, which I also think is odd.

Another oddity is that AF’s product page for the Attila is bare of details. That page has no gun stats and no indication that the gun is in public circulation.

I have the honor of being the first non SHOT Show reviewer of this gun, but the second would be GBGuns on YouTube.

Here’s his review of the gun.

While I’ve had the gun a few months, I only had one of his issues with my gun.

He reported and demonstrated that only one of his two safety levers worked – the right-side lever worked intermittently. I had that issue, as well. Also, I know of two other owners that had the same issue. I detail stripped the gun (to document which internal parts are MIM) and noticed the ambi safeties were easy to remove (usually they are not easy), and that immediately grabbed my attention. I’m thinking that maybe the parts weren’t installed correctly because when reassembling the gun, it was difficult to align the two levers to install them, which is normal. The right lever was functioning.

His other issues were that the gun wasn’t accurate and upon further investigation, he found two issues: 1) the barrel and comp had exessive play, which would affect accuracy – a possible barrel lockup issue; 2) there were copper marks on the inside of his comp – they appear to be bullet strikes.

Another issue he had wasn’t with the gun but was with AF’s customer support. They initially said that they wouldn’t conduct warranty work on the safety since it was deemed an intermittent issue – that doesn’t even make sense, because a safety needs to work every time you enable/disable it. The also initially didn’t want to investigate it for possible lockup issues. They asked him to send a video showing the issue. He sent a portion of the review footage of him troubleshooting the issue and he thinks they noticed that he was a YouTube entity. They changed up and wanted to see the gun to remedy all of the issues.

This is both embarrassing to me and also quite hokey for AF.

I’m a GBGuns Patreon member. There are a bunch of us. We donate funds so that GBGuns can conduct his reviews. Every so often, we vote on guns for him to review. I was one of the members who voted for this gun. I’ve this gun, as well as the AF S15 and, since GBGuns hadn’t ever reviewed an Alpha Foxtrot, I wanted to see his thoughts on the gun. I never considered that he’d receive a bad gun. So, I felt bad. Now, rationally, there were like 40+ others that also voted as I did, so this isn’t something I needed to take blame for, but I consider myself to be pretty knowledgeable about the AF brand, so I was taken by surprise since I’ve rarely heard of this many QC issues with a particular verion of S15.

Also, I was somewhat shocked at how Alpha Foxtrot handled the situation. They only agreed to take the gun in for repair when they suspected that GBGuns was a YouTube entity. I could have issues with mine – would they refuse warranty work in such a case? I’m not a huge YouTuber or influencer. While I think I trust my particular gun, if I have issues with it, I’m doubting that Alpha Foxtrot would fix things – not after seeing what GBGuns experienced. And they still need to fix that gun’s issues.

As well, GBGuns said that manufacturers that do this are untrustworthy and that gun makers such as Bul Armory wouldn’t do such a thing. Yeah, well, they did with me – remember that grip safety issue that I have with my Bul Armory Ultralight? It was sent to them twice and the problem always recurred after 60 days or so. It happened a third time and I opted to not send it back – it’s obvious that they either refuse to fix it or are unable to properly fix it.

I’m sure there are other folks with similar CS stories regarding other brands, too. I say this because I think that all gun makers have times where they fail to get it right regarding warranty committments. I don’t expect every manufacturer to be perfect but I do expect them to support my request within the limit of the warranty. A good gun with bad warranty support = bad gun, in my opinion. If the gun maker comes off as sour or non-accomodating but eventually fully repairs your gun, that’s a bad gun. Having one very bad experience is going to sour the whole overall experience.

This is also the second time I’ve seen AF make decisions based on influencing. It seems as if they’d rather focus on appeasing influencers/entertainers than anyone else. Awhile back, I was speaking with one of their marketing folks in the AF subreddit – he said he wanted to help me and was considering sending me something but wanted to see my YouTube channel first. I wasn’t sure why he was asking, but I provided him the URL to my channel and afterward, he ghosted me. I’m sure he was going to offer to send me a T&E gun but saw that I’ve less than 1000 subscribers and decided that I wasn’t worth it.

AF has always had very weak CS. It made it difficult to advocate for them in the past.

So, I’m going to stop advocating for AF because I’m starting to see that they’re kinda shady.

Categories
1911 2011 Bul Armory double-stack Prodigy DS SAS II Ultralight Springfield Armory

Current Status of Assessing The Prodigy DS Compact

I believe I’m ready to switch over to carrying the Prodigy DS Compact. Right now, I’ve begun to use the Tenicor Certum to carry the gun, but will eventually remove the Streamlight from the Ultralight so that I can install it onto the Prodigy DS – I’ll need to do that to use the More Discreet holster.

I might remove the HS507K from the Ultralight, as well, and install it onto the Prodigy DS, but that would mean that I’d have to re-zero the optic for use on the Prodigy.

I also tested more Hornady Custom XTP 124-gr ammo with the gun. The gun has shot 49 rounds of that ammo. One round of that ammo didn’t feed. I unsuccessfully tried 3 times to get it to feed. When I looked at the round (I still have it), it appears that the projectile has a defect that is making the round out of spec. There are also barbs on the case lip. This is not an issue with the gun. This is also not an issue with that particular box of ammo. Sometimes things aren’t perfect, manufacturing-wise – shit happens. As long as the whole box of ammo wasn’t flawed, it’s OK.

I also bought another box of Speer Gold Dot 124-gr (we now have 2 boxes of that) and a box of Federal HST 124-gr – I’d been using Federal Hydra-Shok but my ammo store was out of that model of ammo. I have not yet tested the Speer GD and the Federal (Hydra-Shok OR HST) through the Prodigy DS, but at least we know that the Hornady Custom XTP works.

I now have 656 rounds thorugh the gun. There have been no feed or extraction issues. The gun is accurate. The trigger has lightened but I also slightly tuned the sear spring (although I did that after the trigger felt that it lightented a bit). Still, the trigger is nowhere as good as the trigger on the Ultralight. The springs are heavier in the Prodigy than the Ultralight, too. I’ll address that after I’ve reached 1000 rounds (will probably add lighter springs, although this is probably a mainspring issue).

Once I’ve begun to carry the Prodigy, I’ll begin the process of finding a gunsmith that can fix the grip safety issue on my Ultralight. I think I might have to send it somewhere reputable, though…there aren’t all that many 1911 gunsmiths around here, and I’m not willing to muck with the gun since I don’t know where to begin.

Categories
1911 2011 Springfield Armory

I Fitted a New Single-Sided Safety to the Prodigy DS Compact

While I’ve a Nighthawk Customs single-sided thumb safety on the way to me, I found a Wilson Combat 6BN Tactical single sided lever in my parts bin. I decided to try that as a test – this part costs far less than the Nighthawk part, so I wanted to practice with it.

Well, I did very well with the fitting, to the point that I decided to actually use the part. It feels good on the gun and the thumb paddle is smaller than what’s on the OEM levers.

Fitting wasn’t difficult, either. I was surprised at how easy it was. My biggest worry was that I wouldn’t fit it in the correct place, but while fitting it, I was also looking at the fitted area of the OEM part and was comparing the two parts as I fitted the new part.

I think 1911s and 2011s look cleaner with a single-sided safety, plus I’m right-handed, so it works for me.

Here are some pics:

I think I’ll put the Nighthawk safety on the Ultralight. There’s also the option of installing it on the XP Pro, as well. [UPDATE: no, there’s no option of installing this on the XP Pro, as the XP Pro is a bit wider than a normal 1911/2011 due to it being designed to use Glock mags, so standard parts will not fit.]

Categories
1911 2011 9mm Springfield Armory

I’ve a Prodigy DS Compact on the way to me!

So, I just completed the order of the next gun.

I had a seriously bad time trying to determine what guns I wanted this year.

I’ll be buying two within the next 30 days.

I just bought a Springfield Armory Prodigy DS Compact 3.5″, from Gunprime. I’d initially planned on buying the 4.25″ Compact but I do a lot of bending and squatting and when carrying AIWB, tasks such as tying shoes is sometimes difficult. I’ve carried Commander 1911s AIWB in the past, but it’s been a while. I was about to order the 4.25″ when I decided to keep it short, since I plan to replace my Bul Armory SAS II Ultralight with the Prodigy Compact.

I’m 100% sure the next gun that I’m buying is another Springfield Armory – I just don’t know which one I’m buying. It’s either the Prodigy 5″ (maybe Comp) or the 5″ Emissary AOS in 9mm. As I don’t have a full-size 1911/2011 in 9mm, I’d initially wanted a full sized prodigy, but the 5″ Emissary is BEAUTIFUL! I was locked onto a 5″ Prodigy Comp until I remembered the Emissary. There’s a very high chance I’ll end up getting the Emissary.

So, the wait is on. I’ve never ordered from Gunprime before, but I’ve been aware of them and have looked at their stock of guns in the past. I’m not sure how prompt they are in processing and shipping guns. There are several popular gun stores that I avoided because they insist on a 5-10 day processing regimen…that’s BS…yeah, I know they’re busy but waiting 10 days to have a gun processed is quite lame. What the hell – that’s like two business weeks!

Knowing my luck, this gun will come when I’m away. I’ve business in CA and will be gone week after next. I ordered this gun late Thursday night (3/20). It might not even be looked at until mid-week next week, and I fly out 3/29 and will be away a full week. That’s how my Ultralight came in – I got a call when I was fishing 300+ miles away. We’ll see how this plays out.

I’m excited but not excited. I know the Prodigy will be good, but it’s probably going to be similar to the Ultralight (not a bad thing exactly). Really, I just need it to be dependable and for ALL the controls to work – the Ultralight’s grip saftey doesn’t function properly (trigger can be dropped without touching the grip safety, although I’ve to hulk up a bit on the trigger). Bul Armory has had the UL twice but can’t (or won’t) fix the grip safety. I think they fucked up the gun when hand-fitting the grip safety – I think they may’ve removed too much material. When metal is removed, it can’t be returned (unless you weld more metal onto the part), which is probably why they’ve had a hard time fixing the issue, although I asked them to replace the part before I returned it the 2nd time, which they did not. I’m not even sure what they did to “repair” it, as the grip safety looked the same as before I sent it back to them, and the saftey was functioning for maye a month before it stopped working again. This is why I won’t buy another Bul Armory – they won’t stand by their own workmanship. I’ve never heard of Springfield Armory doing such a thing, and I’ve never owned a higher end Springfield Armory gun (I’ve two XD9 Mod 2 guns, though).

Of course, I’ll post here with initial thoughts and pics/videos once I’ve received the Prodigy Compact.

UPDATE (3/21/2025): It’s already shipped…Gunprime FTW! It’s supposed to be delivered early morning on Tuesday, via UPS. This is good. I do not know the receiving FFL’s policy on transfers (not sure how long I’ll have to wait for them to process it). They receive it on 3/25. I fly out on 3/29. That’ll leave 3/25 – 3/28 for them to process it. The earlier the better, so that I can have a day or 3 with the gun before I fly out. I’ve not used my range for a transfer since I’ve been a member (2+ years). I’ve been using a different store for that, but my range’s transfer fees are cheap, and I get a discount as a member. I’m curious how this will go, and excited, as well.

Categories
Bul Armory SAS II Ultralight Weapon-Mounted Light

I Lost My Weapon-Mounted Light

I recently started using a weapon-mounted light (WML), carrying it on my Bul Armory SAS II Ultralight. I lost it when I took the gun to the range for practice – it fell off while I was shooting. I did not become aware that the light was missing until almost 2 weeks later!

There are some things to remember and prepare for when usually WMLs.

WMLs usually require a holster that keys off the light. If you lose the light, you’ll be unable to properly carry the gun if you only have a holster that requires a WML. I didn’t notice that the light was gone – it still fit into the holster but the fit wasn’t proper. I’ve no idea why I didn’t notice it intially. The only reason I noticed that the light was gone was because I removed the gun from the holster to check the light and it wasn’t on the gun.

If you lose a light, you should be prepared by either having a backup light or a holster that will allow you use without a WML. In my case, I just pivoted back to using the Tenicor Certum 3, but I was irritated that I’d lost a $100 light and irritated that I had to go back to the Certum, as I’d just started using the QVO Tactical holster.

Also, a good thing to do would be to check your lane/booth before leaving, to ensure that you’re not leaving equipment. I always check and I did check that night but didn’t see the light in the booth (it fell forward of the firing line and was lying on the ground), so a good check would be to ensure that your light is still mounted to your gun before you leave the range.

I contacted my range and shared with them that I’d lost the light at the range and provided them the lane I was using, the make and model of the light, and the date/time I was at the range. I also posted about losing the light on Reddit. Someone replied to the Reddit post stating that they saw the light immediately after I’d left the range (it fell forward of the firing line and was lying on the ground). He said he reported it to the range officer and asked the range officer to retrieve it. He told me to contact the range and ask for Andy.

I contacted the range via their web page and they looked at the camera footage and stated that they couldn’t see the light on my gun and didn’t even know if they were looking at the correct lane. I told them what I was wearing and what I was shooting and told them that the light may’ve come off the gun very soon after shooting it and to not rely on the footage. I told them that I’d checked the lane before leaving and that the light almost certainly fell past the firing line. I also told him that another person on Reddit said that he’d seen the light and had reported it to the RSO and that he’d watched the RSO retrieve it. It was actually a bit surprising that I had to tell them that to get them to become more engaged – it was almost as if they weren’t convinced I’d lost the light at their facility.

The next day, I got a call (I was away from the phone, so a voicemail was left). A supervisor said they’ve my light but that the RSO (Andy) had forgotten it in his range pouch and taken it home. Andy is a college student and was working minimal hours, so he wouldn’t be available to work until 3 days later. He told me to come on on Friday after 3 PM and the light would be available for me to pick up.

I went and picked it up yesterday. They said they’d a few lights (this most be a common issue) and asked for the make/model. They gave me what looked like my light but they must’ve had several TLR-7X lights and I think I received the wrong one. Why do I think that? Because, when I got home and was trying to install the light and it wouldn’t fit. With mine, I didn’t have to change the key – the light fit on the gun with the key that was already on the light. When I got this particular light home, it would not fit on the gun at all. The key was the same (the Universal 1 key) but I think the TLR-7s are packaged with different keys and are built for particular gun types/models. Since I had other keys, I tried those and was able to use a 1913 key that fit the gun (I forgot which one I used).

How do you keep your Streamlight TLR-7 from coming off the gun? They come with e-clips. After selecting a key and installing it, you install the e-clip to the retention screw, which keeps the screw from loosening. I’ve heard many guys on Reddit stating that they don’t use the e-clip. That’s a bad decision, as you’re only supposed to hand-tighten the retention screw. The light comes with two e-clips and you’ve to install it once you’ve chosen the correct key to use. I didn’t install the e-clip because I was unaware that it was 100% necessary. The e-clip is on now, though.

I’m not sure if I should’ve just went back to the range and told them that even though they gave me a TLR-7X, they gave me someone else’s. It may’ve taken weeks and I may not have ever gotten the correct light, so I settled for this.

UPDATE:

I’ve pieced together what happened with my light.

When it was returned to me, it wouldn’t fit on my gun. It fit on my gun before I lost it. I had to change out the key before the light would fit on my gun again. This means someone changed it.

As well, I’d never enabled strobing on the light – this is something that you can’t do by accident, as it requires pressing the “on” button consecutively, ten times…that enables strobing. Someone else had to have done that.

Initially, I’d thought that I had the wrong light, which accounted for why the light wouldn’t fit my gun and why strobing was enabled. I found a picture from before I’d lost the light and that pic had captured the light’s serial number. I compared that with the serial number on the light after it was returned to me. The serial numbers match, meaning the light is the one I had before I lost it. This means that whoever had my light while it was lost was actively using it (ie, it didn’t stay lost, but was taken/used after it was found by someone else).

The RSO that retrieved the light may’ve been using it, and that is sad.

By nature, I always am overly trusting. I mean, I didn’t do anything wrong and didn’t do anything that suggested I was naive. I still feel wronged, though. I grew up less-than-rich. I wasn’t poor, but I wasn’t far from it. I know the value of money. I make great money now but no matter the amount, it’s hard-earned. Gun lights aren’t exactly cheap – mine wasn’t top-of-the-line, but it wasn’t cheap. I’m not a person to just blow off losing a $100 bill and that light was more than $100. I got it back, yes, but not before someone attempted to use and alter it. That’s fucking sad.

I think I’ve to learn to be less trusting.

I talk about all of this in my most recent video:

Categories
Bul Armory SAS II Ultralight

I Decided to Carry My SAS II Ultralight Again

I had the choice to continue to carry my Alpha Foxtrot S15 after my SAS II Ultralight was returned to me from Bul Armory after they repaired it.

Although the S15 is thinner (which helps in concealment), I actually missed carrying my Ultralight, so I decided to switch back to carrying the Ultralight. I just need to take it to the range tomorrow and re-zero the RDS.

There’s something about the Ultralight that keeps attracting me to it. It’s only a few ounces lighter than the S15 but it feels much lighter than it is. Maybe it’s the trigger (it’s GOOD). I love the looks of the gun…the lightening cuts and barrel fluting, as well as the black color with the silver accents.

Right now, the RDS is mounted onto the Ultralight. I mounted the Streamlight (TLR-7 X) to the Ultralight, too. It fits in the QVOT holster without issue. I did have to tighten the holster’s retaining screw quite a bit, as the S15’s rail is wide. I also reinstalled grip tape to the gun.

I’ll look for some SD ammo tomorrow at Cabelas or Trojan Tactical. I may settle for Federal or Hornady. I need to buy several boxes of the good stuff, shoot one box to test the ammo, and then use the other box for carry.

I saw that Bul Armory is now offering the original grip module for purchase. That module has far better grip texturing. It’s $149 on their website. I may order it, but I may add it to my Christmas list so that my wife or kids can buy it for me – if I opt to add it to my Christmas list, I’ll have to wait until after Christmas before I can install it.

I need range ammo as well…I’m almost out and I’ve been buying 500 round blocks of Winchester White Box from Cabelas. When shipping is factored into online prices, the prices are roughly equivalent to what I can buy locally from Cabelas (and I don’t do reman ammo). There are no local LGSs that sell bulk 9mm, so it’s either Cabelas or buying online. I can’t stand the $20-30 shipping of ammo, though. I know ammo is heavy, but damn…

Categories
Bul Armory holster SAS II Ultralight Weapon-Mounted Light

The Ultralight and New Holster are Here!

I’m late in reporting but my SAS II Ultralight is back from Bul Armory.

It was delivered yesterday, on a Sunday – was unexpected, as the shipping info stated it would be delivered on Monday, 9/30.

I tested the gun. It is no longer dropping the hammer without actuating the grip safety.

I’m not sure if I’m going to carry it again or wait, but I did check to see how well the gun fits the Streamlight TLR-7 X – it fits extremely well, without having to change keys (it’s still using the same key it came with out of the box).

I tried fitting the TLR-7 X on my AF1911-S15 – it fits but not fully back to the trigger guard. I’d probably need to change the key to get it further back and I’m not sure if that will adversely change the fitment with the Ultralight, so I’m going to leave the light alone and not change the key.

As well, the new holster was delivered today. As I reported earlier, I bought a 2011 holster from QVO Tactical. I tested fitment today. With the Ultralight and TLR-7 X, it fits perfectly. I did drop the holster down to it’s lowest hole settings (it’s using Double Tacware 5-hole clips) so that it sits low in my waistband.

I also test fitted the S15 to the QVO Tactical holster and TLR-7 X. The S15 is a bit taller at the muzzle than the Ultralight, so there is a bit of rubbing inside the holster. I’m able to account for most of it by loosening the retention (I’ve to do this with all the holsters I use with the S15 – it’s rail is extra beefy).

I also attached velcro to the holster so that I could use my pre-cut foam wedge from Mastermind Tactics. With the wedge, the holster being Commander-sized, and the fact that he has an aggressive wing, the S15 is very concealable. This is why I’m probably going to keep carrying the S15 for a while. No, it is not RDS capable (yet) but I shoot the gun just as well as a gun with an RDS.

Oh, and yeah, the empty space around the trigger guard is not an issue – ALL holsters that accommodate WML (weapon-mounted lights) have extra space around the trigger. That’s unavoidable.

I think I should’ve looked at custom holsters a long time ago. Tenicor is great, but being able to tune a holster to your specific needs is a powerful thing.

Categories
1911 2011 Bul Armory SAS II Ultralight

SAS II Ultralight Is On It’s Way Back from Repair

I posted here that the Ultralight had to be sent back to Bul Armory for repair (again).

It is September 27th and I just got an email that the UL is on it’s way back to me. They received it September 11th.

The notes they provided:

The pistol underwent a full inspection where we made sure all the different components are within spec.

We then adjusted the main spring and test fired the pistol and the pistol works well as it should. 

I’m kinda wary, as the pistol itself was working well when I sent it to them…the issue was that the grip safety wasn’t working properly.

It should be back to me on October 1st.

If it’s not fixed (as I suspect), I’ll stop carrying it. I may sell it to finance a different 2011. I may research to see if I can fix it on my own. Or, I may find a gunsmith that can fix it.

I may be overly worried about this, but I don’t think that the issue was a mainspring adjustment issue, especially since since Bul Armory has had the chance to fix this (twice now). I do not have any other 1911 or 2011 that has ever had this issue and I don’t believe mainsprings just loose adjustability out of the blue to the point that the grip safety stops working.

Categories
1911 2011 Bul Armory SAS II Ultralight

SAS II Ultralight Sent Back to Bul Armory for Repair

The grip safety was not stopping the hammer from falling.

This occurred back in January 2024 and I sent it back to Bul Armory then.

When I received it back, I tested it and the grip safety was functional.

Eight months later, I checked again, and the hammer is dropping again, although I’ve to hulk up on the trigger to get it to drop.

I went to Reddit and asked why this would be occurring and I got several answers. The first two were basically the same answer – that whoever built the gun removed too much material on the grip safety when fitting the part.

The last answer wasn’t really an answer…it was more of an accusation that I wasn’t engaging the grip safety fully, which excessively wore the part over time. I told the guy that that wasn’t the issue, and thanked him for his time. I highly doubt that was the issue, as I’ve to tightly grip the gun to control it and when I grip, the grip safety is disengaged.

Another guy chimed in stating that he’d had the exact same issue. He said he’d bought his gun from GP Arms, who was a Bul Armory importer up until a month or so before I bought my Ultralight. Gabe said that he’d seen the issue before with BA guns, and he fixed it. The guy said the issue never recurred.

So, this leads me to believe that this is indeed a manufacturing issue.

Keep in mind that the one-year warranty expired back in March 2024.

My options were to:

  1. Get the safety pinned – not an option on a $1500 gun.
  2. Find a gunsmith that could fix the safety – not an option on a $1500 gun.
  3. Reach out to Bul Armory and explain to them that they “fixed” this back in January, only for the issue to recur eight months later. Ask them to fix it under warranty and if they won’t, ask them to diagnose the issue and if the cost was reasonable, I’d pay to have it fixed.
  4. Fix it on my own – last resort option (would find a gunsmith before I did this).

I ended up reaching out to Bul Armory and explaining that whatever fix they applied did not work, that the gun was out of warranty but wasn’t when the “fix” was applied. I asked them to fix it under warranty since their fix didn’t remedy the issue. I explained to them that reliability was important to me, as the gun was a carry gun. I also asked that they ensure the gun stayed fixed this go-around and asked them if they needed to replace parts, to please do so.

Bul Armory honored my request. I sent the gun to them last week – they’ve had it a week, so far.

I’m carrying the Alpha Foxtrot while the SAS II UL is being repaired.

I will post an update once the gun has been returned to me.