Category: XP Comp

Categories
ammo Fusion Firearms Remington XP Comp XP Pro

XP Comp Has Crossed 1000 Rounds!

Last week, I was able to cross the 1000 round goal line with the Fusion Firearms XP Comp.

As well, the last 149 rounds were Remington 124-gr FMJ (green/white box), which I’ve discussed here. There were no failures to fire/feed/extract, nor were there any failures to return to battery.

The gun is very nice to shoot. I believe it’s the finest of all my 2011s. Yes, it’s even better than my Bul Armory, but, of course, it’s going to shoot better than my other 2011s since all of them are smaller in size (and are not compensated).

Now that I’ve reached the 1000 round goal, my next task is to remove the firing pin retaining pin. I’m not currently able to remove it. I had the same issue with the XP Pro but was able to remove it with some effort. I refitted it once I removed it. I’ll be doing the same with the XP Comp. The firing pin stop plate can be more easily removed by removing the optic or optic plate – you can tap the top of the stop plate to remove it.

I still need to decide on which gun to focus on next. I’m not really caring to put 1000 rounds through the Kuna. I’m probably going to chose a gun that is close to the 1000 round goal. The Bersa Thunder Plus currently has 773 rounds through it. The PSA AK-V has 740 rounds through it. My Glock 19 Gen 4 has 679 rounds. The Beretta PX4 has 621 rounds.

I’m leaning toward choosing the Beretta, but it would be nice to have the AK-V cross the 1000-round threshold, and it’s not far from that goal.

On another note, I’ve found that the Alpha Foxtrot Attila, while it will shoot the Remington 124-gr ammo, it hits maybe 2″ higher than other ammo (at 10 yards). I was curious about that, so I shot 15 rounds of Federal SD ammo (which is 124-gr). That ammo hit where I was aiming. That is annoying, as I just bought 1000 rounds of that ammo. I do not want to purchase a second set of 9mm ammo for use with the Attila, so I may just shoot it regardless of the issue.

Categories
2011 ammo Fusion Firearms range ammo Remington XP Comp

Bought Remington 124-gr Range Ammo

I was set on Magtech steel-cased ammo, but the Fusion Firearms 2011s do not like it. I know it’s the ammo and not the guns because they’ll eat any other brand of ammo.

I bought 1000 rounds of Remington 124-gr FMJ (green/white box) to address the FF issues of failing to return to battery.

I tested the Remingon by shooting 200 rounds of it through the XP Comp. The XP Comp ate it all without issue.

I shot the rest of the 1000-round batch of Magtech through the AF Attila.

I don’t believe in every gun having to accept all types of ammo, especially if some ammo brands are out-of-spec.

Categories
1911 2011 9mm disassembly Fusion Firearms XP Comp XP Pro

I Was Finally Able to Remove The Firing Pin Stop From The XP Pro!

I’d posted in the past my disassembly issues with the Fusion Firearms XP Pro – here and here.

In both of those posts, I elaborate on my frustrations with being unsuccessful in removing the firing pin stop.

There was a guy on Reddit that posted about his experience with this – the post is here. He explained how he removed the firing pin stop.

I was going to mimic his steps but noticed that I could attempt to remove it from the top of the slide. A few weeks ago, I’d removed the optic from the XP Pro (to use it on the XP Comp). When I removed it, I noticed that the top of the firing pin stop protrudes upward. I thought I’d try to remove the stop from the top, since it was easily accessible.

I was finally able to remove it!

I removed the rear sight plate and got a big-tipped brass punch, using it to tap hard on the top of the plate. It was tricky since I had to also push in the firing pin when doing it. Three hard whacks got it loosened and it was easy to fully remove after doing that.

I spent the past 2 hours filing the stop plate so that it wouldn’t be so difficult to remove in the future. It was a total PITA – LOTS of filing on that part just to get it back on without a hammer and punch. It’s snug but nothing like out of the box.

I’m still evauluating the XP Comp, and I’ve the optic dialed in, so I’m going to wait until I’m done testing before I do the Comp.

Categories
1911 2011 9mm double-stack Fusion Firearms XP Comp XP Pro

I Was FINALLY Able To Obtain Support From Fusion Firearms!

Back in April, I tried to reach out to Fusion Firearms. I was unsuccessful. Why was I trying to contact Fusion Firearms? My XP Comp came with two RMSc plates instead of an RMR and RMSc.

I tried to reach out to them several times, without success, so I gave up. I had to remove the RMR plate that I was using on the XP Pro so that I could use it on the XP Comp.

Last week, I tried again, using their online support system. This time I was able to get through to Tyler. I had included a picture of the two optic plates that came with my XP Comp, which was enough to get him to send an RMR plate to me.

The RMR plate arrived yesterday. I will eventually use it on the XP Pro, once I obtain another RMR optic. Speaking of which, I might actually just get another RMSc-footprinted optic. There are a few RMSc optics that have large windows now. I just need an optic with a large view-port, as that’s what I prefer.

Categories
2011 ammo Fusion Firearms range ammo recoil spring steel-cased XP Comp XP Pro

I Changed the XP Comp’s Recoil Spring to 10-lb!

The last two range visits, I’ve been shooting my XP Comp 2011, attempting to test/review from an owner standpoint.

I’ve been shooting steel-cased ammo lately, specifically Magtech 115-gr FMJ. My Alpha Foxtrot Attila just eats up that ammo, without complaint. Both of my Fusion Firearms 2011s hate that ammo, though. I’ve both the XP Pro and XP Comp. While they eat will shoot the ammo, they ocassionally will not fully go back into battery (sometimes, but not always).s

The last range visit, I actually anticipated the issue and bought some brass-cased Federal 115-gr FMJ. I shot much of that ammo through both XPs, without issue (50 rounds of it). Whenever I’d swap back to the Magtech (purposely attempting to determine if it was an ammo issue), the failures would occur, so I know this is due to the ammo.

Now, this particular make/model of ammo is using polished steel casings, so it’s not the case coating that’s the issue. I think the ammo is slightly underpowered – most steel-cased ammo is cheaply made.

A while back, I bought a spring kit from Fusion Firearms. That kit comes with 7-, 9-, 10-, and 13-lb springs. The XP Comp comes with an 8-lb spring. As I didn’t think the 9-lb spring would cure the issue, I opted to install the 10-lb spring instead.

I also conducted research and the above is a satisfactory solution. Alternative solutions would be to switch to a better ammo type (brass cased or a make/model with a known good reliability history).

I do not blame the ammo as the cause of this issue, as most guns with comps will have light sprints and this is a known thing with the XP Comp. As well, the XP Pro has light springs from the factory, so that’s why it was exhibiting the same issue.

My fix will hopefully resolve the issue (at least with the XP Comp.

While I love Magtech ammo, I might need to switch to something with a bit more power, at least until the XP reaches 1000 rounds. I may go back to Winchester White Box, as it has power.

UPDATE (8/17/2026): So, the change to the 10-lb recoil spring did not help. The gun (both of them) does NOT like this ammo. I’ll be putting the 8-lb spring back into the gun and then I’ll be buying some cheap Winchester or Herter’s just to get some rounds through the gun. The gun isn’t finnicky, as it’ll eat other ammo. It just doesn’t like the Magtech steel cased ammo. I’m getting low with the Magtech anyways – maybe I’ll buy non-steel cased Magtech next. I just need something that works that’s preferrably cheap (in price).

UPDATE (8/21/2026): Today, I removed the 10-lb recoil spring and re-installed the 8-lb spring in the XP Comp. I decided to buy a second set of ammo for this gun – I bought the military/LEO Winchester 115-gr brass cased ammo (brown box). The XP Comp at it all. Some folks might say the gun is finnicky. Nah…it just doesn’t like the cheap stuff. Magtech is good but it is cheap (purposely so, for range shooting). It may also be a combination of dislike of the ammo and the gun being under-sprung. As well, I didn’t like the 10-lb spring because the gun was different with that spring – it felt somewhat harsh, recoil-wise.

Categories
Alpha Foxtrot Attila Fusion Firearms recoil rod recoil spring XP Comp

My Alpha Foxtrot Attila Now Has Over 1000 Rounds!

Yesterday, I went to the range with a focus to push to 1000 rounds. I wouldn’t have been difficult, as I already had 861 rounds through the gun before yesterday’s range visit.

It how has 1084 rounds through it. There were no fails to feed or extract this range visit, nor with any range visit. The 1084 rounds were error-free.

I didn’t post the information here, but during the range visit previous to yesterday’s, the recoil spring assembly (RSA) deconstructed. I was not aware that the recoil spring rod was a two-piece system and is screwed together. Well, the pieces became unscrewed. I wasn’t even aware it happened because I was focused on the target when shooting. I emptied the magazine and then looked down on the table to see the recoil rod lying on the table. I shoot with a GoPro and, when I got home, I reviewed the footage. The rod popped out but the gun still operated – I was able to finish the magazine without issue.

Does that constitute a failure? No. There was no stoppage and the gun continued to function.

I was able to reconstruct the RSA and applied thread locker to the rod when reassemblying it.

Needless to say, I’m impressed, especially since I’m currently carrying the gun, but I’m still planning to buy a DPM recoil spring assemby to replace the OEM RSA.

Next, I plan to test a 15-round Glock 48 magazine. I just need to buy one online since I can’t find them locally.

So, the goal was to reach 1000 rounds. I’ve achieved that goal, now I need to work on the 1000 round review.

The next gun to push to 1000 rounds will be the Fusion Firearms XP Comp, and that’s going to be fun!

Categories
1911 2011 9mm Fusion Firearms Glock 17 magazines XP Comp XP Pro

RWB Glock 17 Mags Are Too Tight Of A Fit For Fusion Firearms XPs

I bought a few extra Glock 17 magazines for my Fusion Firearms XPs. They arrived today.

I’ve a handful of KCI magazines (not the sets that came with my XPs). While they fit, I don’t like them, as the springs are really weak. They’re weak straight out of the packaging.

Well, I’ll give it to the KCI mags – at least they actually fit into the gun. The RWB Glock mags do not fit. I can get them maybe halfway inserted before they bind.

To be fair, I think Fusion Firearms built their XP guns around the KCI mags, as this is a common problem – the mag well is rather tight.

They fit now, though, because I took sandpaper to them. They fit, but they look like ass, even after using smaller grit sandpaper to lessen the coarseness of the scoring. They won’t drop out of the gun – I have to pull them out (they pull out with a very small amount of effort). Over time, they’ll wear-in.

This weekend, I’ll try to visit some local gun shops in an effort to obtain a few more mags. I don’t have time to order a different brand, as today is 6/26 and the new laws take affect on 7/1.